Recommended Residential Construction for the Gulf Coast Building on Strong and Safe Foundations FEMA 550 / July 2006 FEMA About the Cover On August 29, 2005, Hurricane Katrina struck the Gulf Coast with recordbreaking storm surge that destroyed foundations and devastated homes from Louisiana east to Alabama. Katrina was so destructive that engineers assessing the carnage no longer looked for “success stories” (i.e., homes that were only moderately damaged), but rather searched for “survivor” homes that, while extensively damaged, still bore a slight resemblance to a residential building. Hurricane Katrina proved that, without strong foundations, homes on the coast can and will be destroyed. Recommended Residential Construction for the Gulf Coast Building on Strong and Safe Foundations FEMA 550 / July 2006 FEMA RECOMMENDED RESIDENTIAL CONSTRUCTION FOR THE GULF COAST Acknowledgments FEMA would like to thank the following individuals who provided information, data, review, and guidance during the preparation of this report. Principal Authors Bill Coulbourne, PE URS Corporation Matt Haupt, PE URS Corporation Scott Sundberg, PE URS Corporation David K. Low, PE DK Low & Associates, LLC Jimmy Yeung, PhD, PE Greenhorne and O’Mara, Inc. John Squerciati, PE Dewberry and Davis, LLC Contributors and Reviewers John Ingargiola FEMA Headquarters Shabbar Saifee FEMA, Region IV Dan Powell FEMA, Region IV Alan Springett FEMA, Region IV Keith Turi FEMA Headquarters Christopher Hudson FEMA Headquarters Christopher P. Jones, PE Dan Deegan, PE, CFM PBS&J Ken Ford National Association of Homebuilders (NAHB) Mike Hornbeck Gulf Construction Company, Inc. iii David Kriebel, PhD, PE U.S. Naval Academy Jim Puglisi Dewberry and Davis, LLC John Ruble Bayou Plantation Homes Bob Speight, PE URS Corporation Naomi Chang Greenhorne and O’Mara, Inc. Deb Daly Greenhorne and O’Mara, Inc. Julie Liptak Greenhorne and O’Mara, Inc. Wanda Rizer Design4Impact INTRODUCTION Building on strong and safe foundations Intent of the Manual The intent of the manual is to provide Gulf Coast homebuilders, contractors, and local engineering professionals with a series of recommended foundation designs that will help create safer and stronger buildings along the Gulf Coast. The use of these designs is intended to cover many of the home styles anticipated for the construction effort. The foundations may differ somewhat from traditional construction techniques; however, they represent what are considered to be some of the better approaches to constructing strong and safe foundations in the hazardous areas along the Gulf Coast. The objectives used to guide the development of this manual are: n To provide residential foundation designs that will require minimal engineering oversight n To provide foundation designs that are flexible enough to accommodate many of the homes identified in A Pattern Book for Gulf Coast Neighborhoods prepared for the Mississippi Governor’s Rebuilding Commission on Recovery, Rebuilding and Renewal (see Appendix B) n To utilize model layouts so that many homes can be constructed without significant additional engineering efforts The focus of this document is on the foundation of residential buildings. The assumption is that those who are designing and building new homes will be responsible for ensuring that the building itself is designed according to the latest building code (International Building Code [IBC], International Residential Code [IRC], and FEMA guidance) and any local requirements. The user of this manual is directed to other publications that also address disaster-resistant construction (see Appendix G). Figure 1. Damage to residential properties as a result of Hurricane Katrina's winds and storm surge. Note the building that was knocked off its foundation (circled). INTRODUCTION xi Although the foundation designs are geared to the coastal environment subject to storm surge, waves, floating debris, and high winds, several are suitable for supporting homes on sites protected by levees and floodwalls. For protected sites, wave loads may be less than those in an exposed coastal environment and, therefore, the designs presented in this manual may be conservative for such areas. This manual contains closed foundation designs for elevating homes up to 8 feet above ground level and open foundation designs for elevating homes up to 15 feet above ground level. These upper limits are a function of constructability limitations and overturning and stability issues for more elevated foundations. Eight-foot tall foundations are a practical upper limit for 8-inch thick reinforced concrete masonry unit (CMU) walls exposed to flood forces anticipated in non-coastal A zones. The upper limit of 15 feet for open foundations was established by estimating the amount a home needs to be elevated to achieve the 2005 Advisory Base Flood Elevations (ABFEs). The ABFEs published in the Hurricane Recovery Maps were compared to local topographic maps for the Gulf Coast. The comparison revealed that approximately 80 percent of the homes damaged by Hurricane Katrina could be elevated to the ABFEs on foundations that are 15 feet or less in height. Using the Manual The following information is needed to use this manual: n Design wind speed and the Design Flood Elevation (DFE) at the siten The flood zone(s) at the siten Building layoutn Topographic elevation of existing building site n Soil conditions for the site. Soil condition assumptions used in the load calculations are intentionally conservative. Users are encouraged to determine soil conditions at the site to potentially improve the cost-effectiveness of the design. Most of the information can be obtained from the local building official or floodplain manager. This document is not intended to supplant involvement from local design professionals. While the designs included can be used without modification (provided that the home to be elevated falls within the design criteria), consulting with local engineers should be considered. Local engineers may assist with the following: n Incorporating local site conditions into the design CAUTION: Although sites inside levees are not exposed to wave loads, sites immediately adjacent to floodwalls and levees can be exposed to extremely high flood velocities and scour if a breach occurs. Design professionals should be consulted before using these foundation designs on sites close to floodwalls or levees to determine if they are appropriate. n Addressing and supporting unique features of the home n Allowing use of value engineering to produce a more efficient design These designs have been developed to support homes with a range of dimensions, weights, and roof pitches. Figure 2 schematically shows the diverse range of dimensions and roof pitches. Appendix C contains a complete list of criteria and assumptions used in these designs. This manual concentrates on foundations that resist the extreme hurricane wind and flooding conditions found throughout the Gulf Coast. For successful, natural hazard-resistant installations, both the foundation and the home it supports must be properly designed and constructed to take all loads on the structure into the ground through the foundation. Constructing the home to meet all the requirements of the IBC or the IRC is a minimum requirement to producing hazard-resistant homes. However, any model code must contain minimum requirements and best practice approaches for improved resistance to natural hazards. To gain the benefits of a “best practices” approach, readers are directed to publications such as FEMA 499, Home Builder’s Guide to Coastal Construction Technical Fact Sheet Series, and FEMA 55, Coastal Construction Manual. A more complete list of available publications is contained in Appendix G. Figure 2. Schematic of range of home dimensions and roof pitches Organization of the Manual There are five chapters and seven appendices in this manual. The intent is to cover the essential information in the chapters and provide all the details in the appendices. Chapter 1 provides a description of the different types of hazards that must be considered in the design of a residential building foundation in the Gulf Coast area. The primary issues related to designing foundations for residential buildings are described in Chapter 2. Chapter 3 provides guidance on how to determine the magnitude of the loads placed on a building by a particular natural hazard event or a combination of events. The different foundation types and methods of construction foundation for a residential building are discussed in Chapter 4. Chapter 5 and Appendix A present foundation designs to assist the homebuilders, contractors, and local engineering professionals in developing a safe and strong foundation. In addition to Chapters 1 through 5 and Appendix A, the following appendices are presented herein: n Appendix B presents examples of how the foundation designs in this manual can be used with some of the houses in the publication A Pattern Book for Gulf Coast Neighborhoods. n Appendix C provides a list of assumptions used in developing the foundation design presented in this manual. n Appendix D provides detailed calculations on how to design the foundation of residential buildings. Two examples, one for open foundations and the other for closed foundations, are presented. n Appendix E provides cost information that the homebuilders can use to estimate the cost of installing the foundation systems proposed in this manual. n Appendix F includes a list of fact sheets contained in FEMA 499 that are referenced in this manual. n Appendix G presents a list of references and other FEMA publications that can be of assistance to the users of this manual. n Appendix H contains a glossary of terms used in the manual. n Appendix I defines abbreviations and acronyms used in the manual. Limitations of the Manual This manual has been provided to assist in the reconstruction efforts after Hurricane Katrina. Builders, architects, or engineers using this manual assume responsibility for the resulting designs and their performance during a natural hazard event. The foundation designs and analyses presented in this manual were based on the American Society of Civil Engineers (ASCE) 7-02 and the 2003 version of the IRC. While FEMA 550 was being developed, ASCE released its 2005 edition of ASCE 7 (ASCE 7-05) and the International Code Council (ICC) issued their 2006 editions of the IBC and IRC. The ASCE 7 revisions did not affect the load calculations controlling the designs and there were no substantive flood provision changes to the IRC that affect foundation designs in coastal areas. RECOMMENDED RESIDENTIAL CONSTRUCTION FOR THE GULF COAST Table of Contents Acknowledgments..........................................................................................................................iii Introduction .....................................................................................................................................ix Chapter 1. Types of Hazards........................................................................................................1-1 1.1 High Winds.........................................................................................................................1-1 1.2 Storm Surge........................................................................................................................1-4 1.3 Flood Effects.......................................................................................................................1-6 1.3.1 Hydrostatic Forces...................................................................................................1-6 1.3.2 Hydrodynamic Forces.............................................................................................1-7 1.3.3 Waves........................................................................................................................1-8 1.3.4 Floodborne Debris................................................................................................1-10 1.3.5 Erosion and Scour.................................................................................................1-10 Chapter 2. Foundations.................................................................................................................2-1 2.1 Foundation Design Criteria...............................................................................................2-1 table of contents vi Building on strong and safe foundations 2.2 Foundation Design in Coastal Areas ................................................................................2-2 2.3 Open and Closed Foundations in Coastal Areas.............................................................2-4 2.3.1 Open Foundations..................................................................................................2-4 2.3.1.1 Piles...........................................................................................................2-4 2.3.1.2 Piers...........................................................................................................2-7 2.3.2 Closed Foundations................................................................................................2-8 2.3.2.1 Perimeter Walls........................................................................................2-9 2.3.2.2 Slab-on-Grade........................................................................................2-10 2.4 Introduction to Foundation Design and Construction ................................................2-10 2.4.1 Site Characterization............................................................................................2-10 2.4.2 Types of Foundation Construction......................................................................2-11 2.4.2.1 Piles.........................................................................................................2-11 2.4.2.2 Diagonal Bracing of Piles......................................................................2-12 2.4.2.3 Knee Bracing of Piles.............................................................................2-13 2.4.2.4 Wood-Pile-to-Wood-Girder Connections..............................................2-14 2.4.2.5 Grade Beams in Pile/Column Foundations.........................................2-15 Chapter 3. Foundation Design Loads.........................................................................................3-1 3.1 Wind Loads........................................................................................................................3-2 3.2 Flood Loads........................................................................................................................3-3 3.2.1 Design Flood and Design Flood Elevation (DFE)................................................3-4 3.2.2 Design Stillwater Flood Depth...............................................................................3-5 3.2.3 Design Wave Height................................................................................................3-5 3.2.4 Design Flood Velocity.............................................................................................3-6 3.3 Hydrostatic Loads..............................................................................................................3-7 3.4 Wave Loads ........................................................................................................................3-8 3.4.1 Breaking Wave Loads on Vertical Piles..................................................................3-8 3.4.2 Breaking Wave Loads on Vertical Walls.................................................................3-9 3.5 Hydrodynamic Loads.......................................................................................................3-11 Table of contents vii 3.6 Debris Impact Loads........................................................................................................3-12 3.7 Localized Scour................................................................................................................3-14 3.7.1 Localized Scour Around Vertical Piles................................................................3-15 3.7.2 Localized Scour Around Vertical Walls and Enclosures.....................................3-15 3.8 Flood Load Combinations...............................................................................................3-16 Chapter 4. Overview of Recommended Foundation Types and Construction for the Gulf Coast.................................................................................................................................4-1 4.1 Critical Factors Affecting Foundation Design..................................................................4-2 4.1.1 Wind Speed.............................................................................................................4-2 4.1.2 Elevation..................................................................................................................4-2 4.1.3 Construction Materials...........................................................................................4-3 4.1.3.1 Masonry Foundation Construction.........................................................4-3 4.1.3.2 Concrete Foundation Construction........................................................4-3 4.1.3.3 Field Preservative Treatment for Wood Members..................................4-4 4.1.4 Foundation Design Loads......................................................................................4-5 4.2 Recommended Foundation Types for the Gulf Coast.....................................................4-7 4.2.1 Open Foundation: Timber Pile (Case A)..............................................................4-8 4.2.2 Open Foundation: Steel Pipe Pile with Concrete Column and Grade Beam (Case B)........................................................................................................4-9 4.2.3 Open Foundation: Timber Pile with Concrete Column and Grade Beam (Case C).................................................................................................................4-11 4.2.4 Open Foundation: Concrete Column and Grade Beam with Slabs (Cases D and G)....................................................................................................4-12 4.2.5 Closed Foundation: Reinforced Masonry – Crawlspace (Case E).....................4-13 4.2.6 Closed Foundation: Reinforced Masonry – Stem Wall (Case F)........................4-14 Chapter 5. Foundation Selection................................................................................................5-1 5.1 Foundation Design Types..................................................................................................5-1 5.2 Foundation Design Considerations..................................................................................5-2 5.3 Cost Estimating..................................................................................................................5-4 5.4 How to Use This Manual...................................................................................................5-4 5.5 Design Examples................................................................................................................5-7 Appendices Appendix A Foundation Designs Appendix B Pattern Book Design Appendix C Assumptions Used in Design Appendix D Foundation Analysis and Design Examples Appendix E Cost Estimating Appendix F Referenced Fact Sheets from FEMA 499 Appendix G FEMA Publications and Additional References Appendix H Glossary Appendix I Abbreviations and Acronyms 1 TYPES OF HAZARDS 1- Building on strong and safe foundations The most current design wind speeds are provided by the American Society of Civil Engineers (ASCE) document Minimum Design Loads for Buildings and Other Structures (ASCE 7). ASCE 7 is typically updated every 3 years. The 2002 edition ASCE 7-02 is referenced by the following model building codes: the 2003 editions of the International Building Code (IBC), the International Residential Code (IRC), and the NFPA 5000, Building Construction and Safety Code, published by the National Fire Protection Association (NFPA). Design wind speeds given by ASCE 7 are 3-second gust speeds, not the sustained wind speeds associated with the Saffir-Simpson hurricane classification scale. Figure 1-3 shows the design wind speeds for portions of the Gulf Coast region based on 3-second gusts (measured at 33 feet above the ground in Exposure C). NOTE: Hurricanes are classified into five categories according to the Saffir-Simpson Scale, which uses wind speed and central pressure as the principal parameters to categorize storm damage potential. Hurricanes can range from Category 1 to the devastating Category 5 (Figure 1-2). Hurricanes can produce storm surge that is higher or lower than what the wind speed at landfall would predict. Katrina’s surge was roughly that of a Category 5, although its winds at landfall were only a Category 3. A hurricane that is a Category 3 or above is generally considered a major hurricane. Figure 1-1. Wind damage to roof structure and gable end wall from Hurricane Katrina (2005) (Pass Christian, Mississippi) TYPES OF HAZARDS 1 1- Saffir-Simpson Scale (Category/Damage) Category 1 Hurricane – Winds 74 to 95 mph, sustained (91 to 116 mph, 3-second gust) No real damage to buildings. Damage to unanchored mobile homes. Some damage to poorly constructed signs. Also, some coastal flooding and minor pier damage. Examples: Hurricanes Irene (1999) and Allison (1995). Category 2 Hurricane – Winds 96 to 110 mph, sustained (117 to 140 mph, 3-second gust) Some damage to building roofs, doors, and windows. Considerable damage to mobile homes. Flooding damages piers, and small crafts in unprotected moorings may break. Some trees blown down. Examples: Hurricanes Bonnie (1998), Georges (FL and LA 1998), and Gloria (1985). Category 3 Hurricane – Winds 111 to 130 mph, sustained (141 to 165 mph, 3-second gust) Some structural damage to small residences and utility buildings. Large trees blown down. Mobile homes and poorly built signs destroyed. Flooding near the coast destroys smaller structures with larger structures damaged by floating debris. Terrain may be flooded far inland. Examples: Hurricanes Keith (2000), Fran (1996), Opal (1995), Alicia (1983), Betsy (1965), and Katrina at landfall (2005). Category 4 Hurricane – Winds 131 to 155 mph, sustained (166 to 195 mph, 3-second gust) More extensive curtainwall failures with some complete roof structure failure on small residences. Major erosion of beach areas. Terrain may be flooded far inland. Examples: Hurricanes Hugo (1989), Donna (1960), and Charley (2004). Category 5 Hurricane – Winds greater than 155 mph, sustained (195 mph and greater, 3-second gust) Complete roof failure on many residences and industrial buildings. Some complete building failures with small utility buildings blown over or away. Flooding causes major damage to lower floors of all structures near the shoreline. Massive evacuation of residential areas may be required. Examples: Hurricanes Andrew (1992), Camille (1969), and the unnamed Labor Day storm (1935). Note: Saffir-Simpson wind speeds (sustained 1-minute) were converted to 3-second gust wind speed utilizing the Durst Curve contained in ASCE 7-02, Figure C6-2. Figure 1-2. Saffir-Simpson Scale 1.2 Storm Surge Storm surge is water that is pushed toward the shore by the combined force of the lower barometric pressure and the wind-driven waves advancing to the shoreline. This advancing surge combines with the normal tides to create the hurricane storm tide, which in many areas can increase the sea level by as much as 20 to 30 feet. Figure 1-4 is a graphical depiction of how wind-driven waves are superimposed on the storm tide. This rise in water level can cause severe flooding in coastal areas, particularly when the storm tide coincides with high tides (see Figure 1-5). Because much of the United States’ densely populated Gulf Coast coastlines lie less than 20 feet above sea level, the danger from storm surge is great. In addition, because of the shape and the bathymetery of the Gulf of Mexico, storm surges along the Gulf Coast can be greater than anywhere else in the United States (see Figure 1-6). Figure 1-3. Design wind speed map for portions of the Gulf Coast. Contours are 3-second gust wind speeds (in miles per hour [meters per second]) for Exposure Category C, 33 feet height. Source: ASCE 7-02 Figure 1-4. Graphical depiction of a hurricane moving ashore. In this example, a 15-foot surge added to the normal 2-foot tide creates a total storm tide of 17 feet. Figure 1-5. Storm tide and waves from Hurricane Dennis on July 10, 2005, near Panacea, Florida Source: U.S. Geological Survey (USGS) Sound Waves Monthly newsletter. Photograph courtesy of The Forgotten Coastline (Copyright 2005) Figure 1-6. Comparison of storm surge levels along the shorelines of the Gulf Coast for Category 1, 3, and 5 storms Source: Hurricane Katrina in the Gulf Coast MAT Report (FEMA 549) 1.3 Flood Effects Although coastal flooding can originate from a number of sources, Gulf Coast hurricanes and weaker tropical storms not categorized as hurricanes are the primary cause of flooding (see Figure 1-2). The flooding can lead to a variety of impacts on coastal buildings and their foundations: hydrostatic forces, hydrodynamic forces, waves, floodborne debris forces, and erosion and scour. 1.3.1 Hydrostatic Forces Horizontal hydrostatic forces against a structure are created when the level of standing or slowly moving floodwater on opposite sides of the structure are not equal. Flooding can also cause vertical hydrostatic forces, resulting in flotation. Rapidly rising floodwaters can also cause structures to float off of their foundations (see Figure 1-7). If floodwaters rise slowly enough, water can seep into a structure to reduce buoyancy forces. While slowly rising floodwaters reduce the adverse effects of buoyancy, any flooding that inundates a home can cause extreme damage. 1.3.2 Hydrodynamic Forces Moving floodwaters create hydrodynamic forces on submerged foundations and buildings. These hydrodynamic forces can destroy solid walls and dislodge buildings with inadequate connections or load paths. Moving floodwaters can also move large quantities of sediment and debris that can cause additional damage. In coastal areas, moving floodwaters are usually associated with one or more of the following: n Storm surge and wave runup flowing landward through breaks in sand dunes, levees, or across low-lying areas (see Figure 1-8) Figure 1-7. Building floated off of foundation (Plaquemines Parish, Louisiana) Source: Hurricane Katrina in the gulf coast (FEMA 549) Figure 1-8. Aerial view of damage to one of the levees caused by Hurricane Katrina (photo taken on August 30, 2005, the day after the storm hit, New Orleans, Louisiana). Source: FEMA NEWS PHOTO/ Jocelyn Augustino n Outflow (flow in the seaward direction) of floodwaters driven into bay or upland areas by a stormn Strong currents along the shoreline driven by storm waves moving in an angular direction to the shore High-velocity flows can be created or exacerbated by the presence of manmade or natural obstructions along the shoreline and by “weak points” formed by shore-normal (i.e., perpendicular to the shoreline) roads and access paths that cross dunes, bridges, or shore-normal canals, channels, or drainage features. For example, evidence after Hurricane Opal (1995) struck Navarre Beach, Florida, suggests that flow was channeled in between large, engineered buildings. The resulting constricted flow accelerated the storm surge and caused deep scour channels across the island. These channels eventually undermined pile-supported houses between large buildings while also washing out roads and houses farther landward (see Figure 1-9). 1.3.3 Waves Waves can affect coastal buildings in a number of ways. The most severe damage is caused by breaking waves (see Figures 1-10 and 1-11). The height of these waves can vary by flood zone: V Zone wave heights can exceed 3 feet, while Coastal A Zone wave heights are between 1.5 and 3 feet. The force created by waves breaking against a vertical surface is often ten or more times higher than the force created by high winds during a storm event. Waves are particularly damaging due to their cyclic nature and resulting repetitive loading. Because typical wave periods during hurricanes range from about 6 to 12 seconds, a structure can be exposed to 300 to 600 waves per hour, resulting in possibly several thousand load cycles over the duration of the storm. Wave runup occurs as waves break and run up beaches, sloping surfaces, and vertical surfaces. Wave runup can drive large volumes of water against or around coastal buildings, creating Figure 1-9. During Hurricane Opal (1995), this house was in an area of channeled flow between large buildings. As a result, the house was undermined and washed into the bay behind a barrier island. Source: COastal Construction manual (FEMA 55) hydrodynamic forces (albeit smaller than breaking wave forces), drag forces from the current, and localized erosion and scour. Wave runup under a vertical surface (such as a wall) will create an upward force by the wave action due to the sudden termination of its flow. This upward force is much greater than the force generated as a wave moves along a sloping surface. In some instances, the force is large enough to destroy overhanging elements such as decks or porches. Another negative effect of waves is reflection or deflection, occurring when a wave is suddenly redirected as it impacts a building or structure. Figure 1-10. Storm waves breaking against a seawall in front of a coastal residence at Stinson Beach, California Source: COastal COnStruction manual (FEMA 55) Figure 1-11. Storm surge and waves overtopping a coastal barrier island in Alabama (Hurricane Frederic, 1979) Source: COastal COnStruction manual (FEMA 55) 1.3.4 Floodborne Debris Floodborne debris produced by coastal flood events and storms typically includes decks, steps, ramps, breakaway wall panels, portions of or entire houses, fuel tanks, vehicles, boats, pilings, fences, destroyed erosion control structures, and a variety of smaller objects (see Figure 1-12). In some cases, larger pieces of floodborne debris can strike buildings (e.g., shipping containers and barges), but the designs contained herein are not intended to withstand the loads from these larger debris elements. Floodborne debris is capable of destroying unreinforced masonry walls, light wood-frame construction, and small-diameter posts and piles (and the components of structures they support). Debris trapped by cross bracing, closely spaced pilings, grade beams, or other components is also capable of transferring flood and wave loads to the foundation of an elevated structure. 1.3.5 Erosion and Scour Erosion refers to the wearing and washing away of coastal lands, including sand and soil. It is part of the larger process of shoreline changes. Erosion occurs when more sediment leaves a shoreline area than enters from either manmade objects or natural forces. Because of the dynamic nature of erosion, it is one of the most complex hazards to understand and difficult to accurately predict at any given site along the coast. Short-term erosion changes can occur from storms and periods of high wave activity, lasting over periods ranging from a few days to a few years. Because of the variability in direction and magnitude, short-term erosion effects can be orders of magnitude greater than long-term erosion. Long-term shoreline changes occur over a period of decades or longer and tend to average out the short-term erosion. Both short-term and long-term changes should be considered in the siting and design of coastal residential construction. Refer to Chapter 7 of FEMA 55 for additional guidance on assessing short- and long-term erosion. Figure 1-12. Pier pilings were carried over 2 miles by the storm surge and waves of Hurricane Opal (1995) before coming to rest against this elevated house in Pensacola Beach, Florida. Source: COastal COnStruction manual (FEMA 55) Scour can occur when water flows at high velocities past an object embedded in or sitting on soil that can be eroded. Scour occurs around the object itself, such as a piling or foundation element, and contributes to the loss of support provided by the soil. In addition to any storm or flood-induced erosion that occurs in the general area, scour is generally limited to small, cone- shaped depressions. Localized scour is capable of undermining slabs, pilings, and grade beam structures, and, in severe cases, can lead to structural failure (see Figure 1-13). This document considers these effects on the foundation size and depth of embedment requirements. Figure 1-13. Extreme case of localized scour undermining a slab-on-grade house in Topsail Island, North Carolina, after Hurricane Fran (1996). Prior to the storm, the lot was several hundred feet from the shoreline and mapped as an A Zone on the FIRM. This case illustrates the need for open foundations in Coastal A Zones. Source: COastal COnStruction manual (FEMA 55) 2 FOUNDATIONS 2- Building on strong and safe foundations In addition, the foundation should be constructed with flood-resistant materials below the Base Flood Elevation (BFE). 2.2 Foundation Design in Coastal Areas Building in a coastal environment is different from building in an inland area because: n Storm surge, wave action, and erosion in coastal areas make coastal flooding more damaging than inland flooding. n Design wind speeds are higher in coastal areas and thus require buildings and their foundations to be able to resist higher wind loads. Foundations in coastal areas must be constructed such that the top of the lowest floor (in A Zones) or the bottom of the lowest horizontal structural members (in V Zones) of the buildings are elevated above the BFE, while withstanding flood forces, high winds, erosion and scour, and floodborne debris. Deeply embedded pile or other open foundations are required for V Zones because they allow waves and floodwaters to pass beneath elevated buildings. Because of the increased flood, wave, floodborne debris, and erosion hazards in V Zones, NFIP design and construction requirements are more stringent in V Zones than in A Zones. Some coastal areas mapped as A Zones may also be subject to damaging waves and erosion (referred to as “Coastal A Zones”). Buildings in these areas that are constructed to minimum NFIP A Zone requirements may sustain major damage or be destroyed during the base flood. It is strongly recommended that buildings in A Zones subject to breaking waves and erosion be designed and constructed with V Zone type foundations (see Figure 2-1). Open foundations are often recommended instead of solid wall, crawlspace, slab, or shallow foundations, which can restrict floodwaters and be undermined easily. Figure 2-2 shows examples of building failures due to scour under a slab-on-grade foundation. NFIP Minimum Elevation Requirements for New Construction* A Zone: Elevate top of lowest floor to or above BFE V Zone: Elevate bottom of lowest horizontal structural member supporting the lowest floor to or above BFE In both V and A Zones, many property owners have decided to elevate one full story above grade, even if not required, to allow below-building parking. See Fact Sheet No. 2 of FEMA 499 for more information about NFIP minimum requirements and recommended best practices in A and V Zones (see Appendix F). * For floodplain management purposes, “new construction” means structures for which the start of construction began on or after the effective date of the floodplain management regulation adopted by a community. Substantial improvements, repairs of substantial damage, and some enclosures must meet most of the same requirements as new construction. FOUNDATIONS 2 2- Figure 2-1. Recommended open foundation practice for buildings in A Zones, Coastal A Zones, and V Zones Source: COastal COnstruction manual (FEMA 55) Figure 2-2 Slab-on-grade foundation failure due to erosion and scour undermining and closeup of the foundation failure from Hurricane Dennis, 2005 (Navarre Beach, Florida). 2.3 Open and Closed Foundations in Coastal Areas There are many designs that can be used to elevate buildings above the BFE: open foundations (pile, pier, column) and closed foundations (crawlspace, stem wall, solid wall). Structural fill can also be used to elevate and support stem wall, crawlspace, solid wall, slab- on-grade, pier, and column foundations in areas not subject to damaging wave action and scour. Only open foundations with base members or elements (pilings or beams) located below expected erosion and scour are allowed in V Zones; as a “best practices” approach, open foundations are recommended, but are not NFIP required, in Coastal A Zones. Table 2-1 shows the recommended type of foundation depending on the coastal area. Additional information concerning foundation performance can be found in FEMA 499, Fact Sheet No. 11 (see Appendix F). Table 2-1. Foundation Type Dependent on Coastal Area Foundation Type V Zone Coastal A Zone A Zone Open 4 4 4 Closed 8 NR 4 4 = Acceptable NR = Not Recommended 8 = Not Permitted 2.3.1 Open Foundations Open foundations are required in V Zones and recommended in Coastal A Zones. This type of foundation allows water to pass beneath an elevated building through the foundation and reduces lateral flood loads on the structure. Open foundations also have the added benefit of being less susceptible to damage from floodborne debris because debris is less likely to be trapped. 2.3.1.1 Piles Pile foundations consist of deeply placed vertical piles installed under the elevated structure. The piles support the elevated structure by remaining solidly placed in the soil. Because pile foundations are set deeply, they are inherently more tolerant to erosion and scour. Piles rely primarily on the friction forces that develop between the pile and the surrounding soils (to resist gravity and uplift forces) and the compressive strength of the soils (to resist lateral movement). The soils at the ends of the piles also contribute to resist gravity loads. Piles are typically treated wood timbers, steel pipes, or pre-cast concrete. Other materials like fiber reinforced polyester (FRP) are available, but are rarely used in residential construction. Piles can be used with or without grade beams. When used without grade beams, piles extend to the lowest floor of the elevated structure. Improved performance is achieved when the piles extend beyond the lowest floor to the roof (or an upper floor level) above. Doing so provides resistance to rotation (also called “fixity”) in the top of the pile and improves stiffness of the pile foundation. Occasionally, wood framing members are installed at the base of a wood piling (see Figure 2-3). These members are not true grade beams but rather are compression struts. They provide lateral support for portions of the piling near grade and reduce the potential for column buckling; however, due to the difficulties of constructing moment connections with wood, the compression struts provide very little resistance to rotation. Critical aspects of a pile foundation include the pile size, installation method, and embedment depth, bracing, and their connections to the elevated structure (see FEMA 499 Fact Sheet Nos. 12 and 13 in Appendix F). Pile foundations with inadequate embedment will not have the structural capacity to resist sliding and overturning (see Figure 2-4). Inadequate embedment and improperly sized piles greatly increase the probability for structural collapse. However, when properly sized, installed, and braced with adequate embedment into the soil (with consideration for erosion and scour effects), a building’s pile foundation performance will allow the building to remain standing and intact following a design flood event (see Figure 2-5). When used with grade beams, the piles and grade beams work in conjunction to elevate the structure, provide vertical and lateral support for the elevated home, and transfer loads imposed on the elevated home and foundation to the ground below. Figure 2-3. Compression strut at base of a wood piling. Struts provide some lateral support for the piling, but very little resistance to rotation. Source: COastal COnStruction manual (FEMA 55) Figure 2-4. Near collapse due to insufficient pile embedment (Dauphin Island, Alabama) Source: Hurricane Katrina in the Gulf Coast (FEMA 549) Pile foundations with grade beams must be constructed with adequate strength to resist all lateral and vertical loads. Failures experienced during Hurricane Katrina often resulted from inadequate connections between the columns and footings or grade beams below (see Figure 2-6). Pile and grade beam foundations should be designed and constructed so that the grade beams act only to provide fixity to the foundation system and not to support the lowest elevated floor. If grade beams support the lowest elevated floor of the home, they become the lowest horizontal structural member and significantly higher flood insurance premiums would result. Also, if the grade beams support the structure, the structure would become vulnerable to erosion and scour. Grade beams must also be designed to span between adjacent piles and the piles must be capable of resisting both the weight of the grade beams when undermined by erosion and scour, and the loads imposed on them by forces acting on the structure. Figure 2-5. Successful pile foundation following Hurricane Katrina (Dauphin Island, Alabama) Source: Hurricane Katrina in the Gulf Coast (FEMA 549) Figure 2-6. Column connection failure (Belle Fontaine Point, Jackson County, Mississippi) Source: Hurricane Katrina in the Gulf Coast (FEMA 549) 2.3.1.2 Piers Piers have different design criteria in various locations around the country. As used in the Gulf Coast for residential construction, piers are generally placed on footings to support the elevated structure. Without footings, piers function as short piles and rarely have sufficient capacity to resist uplift and gravity loads. The type of footing used in pier foundations greatly affects the foundation’s performance (see Figure 2-7). When exposed to lateral loads, discrete footings can rotate so piers placed on discrete footings are only suitable when wind and flood loads are relatively low. Piers placed on continuous concrete grade beams or concrete strip footings provide much greater resistance to lateral loads because the grade beams/footings act as an integral unit and are less prone to rotation. Footings and grade beams must be reinforced to resist the moment forces that develop at the base of the piers due to the lateral loads on the foundation and the elevated home (see Figure 2-8). Since pier foundation footings or grade beams are limited in depth of placement, they are appropriate only where there is limited potential for erosion or scour. The maximum estimated depth for long- and short-term erosion and localized scour should not extend below the bottom of the footing or grade beam. Figure 2-7. Performance comparison of pier foundations. Piers on discrete footings (foreground) failed by rotating and overturning while piers on more substantial footings (in this case a concrete mat) survived (Pass Christian, Mississippi) 2.3.2 Closed Foundations A closed foundation is typically constructed using foundation walls, a crawlspace foundation, or a stem wall foundation (usually filled with compacted soil). A closed foundation does not allow water to pass easily through the foundation elements below the elevated building. Thus, these types of foundations are said to obstruct the flow. These foundations also present a large surface area upon which waves and flood forces act; therefore, they are prohibited in V Zones and not recommended for Coastal A Zones. If foundation or crawlspace walls enclose space below the BFE, they must be equipped with openings that allow floodwaters to flow in and out of the area Figure 2-8. Isometric view of an open foundation with grade beam enclosed by the walls (see Figure 2-9 for an isometric view). The entry and exit of floodwater will equalize the water pressure on both sides of the wall and reduce the likelihood of the wall collapsing (see FEMA 499 Fact Sheet No. 15 in Appendix F). Two types of closed foundations are discussed in this manual, perimeter walls and slab-on-grade. 2.3.2.1 Perimeter Walls Perimeter walls are conventional walls (typically masonry or wood frame) that extend from the ground up to the elevated building. They typically bear on shallow footings. Crawlspaces and stem walls are two types of foundations with perimeter walls. Crawlspaces. Crawlspace foundations are typically low masonry perimeter walls, some requiring interior piers supporting a floor system if the structure is wide. These foundations are usually supported by shallow footings and are prone to failure caused by erosion and scour. Figure 2-9. Isometric view of a closed foundation with crawlspace This type of foundation is characterized by a solid perimeter foundation wall around a structure with a continuous spread footing with reinforced masonry or concrete piers. All crawlspace foundation walls in the Special Flood Hazard Area (SFHA) must be equipped with flood openings. These openings are required to equalize the pressure on either side of the wall (see FEMA 499 Fact Sheet Nos. 15 and 26 in Appendix F). However, even with flood vents, hydrodynamic and wave forces in Coastal A Zones can damage or destroy these foundations. Stem Walls. Stem walls (i.e., a solid perimeter foundation wall on a continuous spread footing backfilled to the underside of the floor slab) are similar to crawlspace foundations, but the interior that would otherwise form the crawlspace is filled with soil or gravel that supports a floor slab. Stem wall foundations have been observed to perform better than crawlspace foundations in Coastal A Zones (but only where erosion and scour effects are minor). Flood openings are not required in filled stem wall foundations. 2.3.2.2 Slab-on-Grade A slab-on-grade foundation is concrete placed directly on-grade (to form the slab) with generally thickened, reinforced sections around the edges and under loadbearing walls. The slab itself is typically 4 inches thick where not exposed to concentrated loads and 8 to 12 inches thick under loadbearing walls. The thickened portions of slab-on-grade foundations are typically reinforced with deformed steel bars to provide structural support; the areas not thickened are typically reinforced with welded wire fabrics (WWF) for shrinkage control. While commonly used in residential structures in A Zones, slab-on-grade foundations are prone to erosion and prohibited in V Zones, and are not recommended for Coastal A Zones. Slab-on-grade foundations can be used with structural fill to elevate buildings. Fill is usually placed in layers called “lifts” with each lift compacted at the site. Because fill is susceptible to erosion, it is prohibited for providing structural support in V Zones. Structural fill is not recommended for Coastal A Zones, but may be appropriate for non-Coastal A Zones. 2.4 Introduction to Foundation Design and Construction This section introduces two main issues related to foundation design and construction: site characterization and types of foundation construction. Construction materials and methods (field preservation treatment, substitutions, inspection points) are addressed in Chapter 4. 2.4.1 Site Characterization The foundation design chosen should be based on the characteristics that exist at the building site. A site characteristic study should include the following: n The type of foundations that have been installed in the area in the past. A review of the latest Flood Insurance Rate Map (FIRM) is recommended to ensure that construction characteristics have not been changed. n The proposed site history, which would indicate whether there are any buried materials, or the site has been regraded. n How the site may have been used in the past, from a search of land records for past ownership. n A Soil Investigation Report, which should include: n Soil borings sampled from the site or taken from test pitsn A review of soil borings from the immediate area adjacent to the site n Information from the local office of the Natural Resource Conservation Service (formerly the Soil Conservation Service) and soil surveys published for each county One of the parameters derived from a soil investigation report is the bearing capacity, which measures the ability of soils to support gravity loads without soil shear failure or excessive settlement. Measured in pounds per square foot (psf), soil bearing capacity typically ranges from 1,000 psf for relatively weak soils to over 10,000 psf for bedrock. Frequently, designs are initially prepared on a presumed bearing capacity. It is then the homebuilder’s responsibility to verify actual site conditions. The actual soil bearing capacity should be determined. If soils are found to have higher bearing capacity, the foundation can be constructed as designed or the foundation can be revised to take advantage of the better soils. Allowable load bearing values of soils given in Section 1804 of the 2003 IBC can be used when other data are not available. However, soils can vary significantly in bearing capacity from one site to the next. A geotechnical engineer should be consulted when any unusual or unknown soil condition is encountered. 2.4.2 Types of Foundation Construction 2.4.2.1 Piles A common type of pile foundation is the elevated wood pile foundation, where the piles extend from deep in the ground to an elevation at or above the Design Flood Elevation (DFE). Horizontal framing members are used to connect the piles in both directions. This grid forms a platform on which the house is built (see FEMA 499 Fact Sheet No. 12 in Appendix F). The method of installation is a major consideration in the structural integrity of pile foundations. The ideal method is to use a pile driver. In this method, the pile is held in place with leads while a single-acting, double-acting diesel or air-powered hammer drives the pile into the ground (see Figure 2-10). If steel piles are used, only the hammer driving method mentioned above should be used. For any pile driving, the authority having jurisdiction or the engineer-of-record may require that a driving log is kept for each pile. The log will tabulate the number of blows per foot as the driving progresses. This log is a key factor used in determining the pile capacity. Another method for driving piles is the drop hammer method. It is a lower cost alternative to the pile driver. A drop hammer consists of a heavy weight raised by a cable attached to a power- driven winch and then dropped onto the pile. A less desirable but frequently used method of inserting piles into sandy soil is “jetting,” which involves forcing a high-pressure stream of water through a pipe that advances with the pile. The water creates a hole in the sand as the pile is driven until the required depth is reached. Unfortunately, jetting loosens the soil both around the pile and the tip. This results in a lower load capacity due to less frictional resistance. Jetted piles are not appropriate for the design provided in this manual unless capacity is verified by a geotechnical engineer. Holes for piles may be excavated by an auger if the soil has sufficient clay or silt content. Augering can be used by itself or in conjunction with pile driving. If the hole is full-sized, the pile is dropped in and the void backfilled. Alternatively, an undersized hole can be drilled and a pile driven into it. When the soil conditions are appropriate, the hole will stay open long enough to drop or drive in a pile. In general, this method may not have as much capacity as those methods previously mentioned. Like jetted piles, augered piles are not appropriate for the designs provided in this manual unless the method for compressing the soil is approved by a geotechnical engineer. 2.4.2.2 Diagonal Bracing of Piles The foundation design may include diagonal bracing to stiffen the pile foundation in one or more directions. When installed properly, bracing lowers the point where lateral loads are applied to the piles. The lowering of load application points reduces the bending forces that piles must resist (so piles in a braced pile foundation do not need to be as strong as piles in an unbraced pile foundation) and also reduces lateral movement in the building. Outside pilings are sufficiently designed to withstand external forces, because bracing will not assist in countering Figure 2-10. Pile installation methods Source: COastal COnstruction manual (FEMA 55) these forces. A drawback to bracing, however, is that the braces themselves can become obstructions to moving floodwaters and increase a foundation’s exposure to wave and debris impact. Because braces tend to be slender, they are vulnerable to compression buckling. Therefore, most bracing is considered tension-only bracing. Because wind and, to a lesser extent, flood loads can act in opposite directions, tension-only bracing must be installed in pairs. One set of braces resists loads from one direction while the second set resists loads from the opposite direction. Figure 2-11 shows how tension only bracing pairs resist lateral loads on a home. The braced pile design can only function when all of the following conditions are met: n The home must be constructed with a stiff horizontal diaphragm such as a floor system that transfers loads to laterally braced piles. n Solid connections, usually achieved with bolts, must be provided to transmit forces from the brace to the pile or floor system. The placement of the lower bolted connection of the diagonal to the pile requires some judgment. If the connection is placed too high above grade, the pile length below the connection is not braced and the overall bracing is less strong and stiff. If the connection is placed too close to grade, the bolt hole is more likely to be flooded or infested with termites. Because the bolt hole passes through the untreated part of the pile, flooding and subsequent decay or termite infestation will weaken the pile at a vulnerable location. Therefore, the bolt hole should be treated with preservative after drilling and prior to bolt placement. The braced wood pile designs developed for this manual use steel rods for bracing. Steel rods were used because: n Steel has greater tensile strength than even wide dimensional lumber. n There are fewer obstructions to waves and floodborne debris. n The rod bracing can easily be tensioned with turnbuckles and can be adjusted throughout the life of the home. n A balanced double shear connection is two to three times stronger than a wood to wood connection made with 2-inch thick dimensional lumber. Alternative bracing should only be installed when designed by a licensed engineer. 2.4.2.3 Knee Bracing of Piles Knee braces involve installing short diagonal braces between the upper portions of the pilings and the floor system of the elevated structure. The braces increase the stiffness of an elevated pile foundation and can be effective at resisting the lateral forces on a home. While knee braces do not stiffen a foundation as much as diagonal bracing, they do offer some advantages over diagonal braces. For example, knee braces present less obstruction to waves and debris, are shorter than diagonal braces, and are usually designed for both tension and compression loads. Unlike diagonal braces, knee braces do not reduce bending moments in the piles (they can actually increase bending moments) and will not reduce the diameter of the piles required to resist lateral loads. The entire load path into and through the knee brace must be designed with sufficient capacity. The connections at each end of each knee brace must have sufficient capacity to handle both tension and compression and to resist axial loads in the brace. The brace itself must have sufficient cross-sectional area to resist compression and tensile loads. Due to the complexity of knee bracing, they have not been used in the foundation designs included in Appendix A of this document. 2.4.2.4 Wood-Pile-to-Wood-Girder Connections Wood piles are often notched to provide a bearing surface for a girder. However, a notch should not reduce more than 50 percent of the pile cross-section (such information is typically provided by a designer on contract documents). For proper load transfer, the girder should bear on the surface of the pile notch. Figure 2-11. Diagonal bracing schematic Although connections play an integral role in the design of structures, they are typically regarded as the weakest link. The connection between a wood pile and the elevated structure should be designed by an engineer (see FEMA 499 Fact Sheet No. 13 in Appendix F). 2.4.2.5 Grade Beams in Pile/Column Foundations Grade beams are sometimes used in conjunction with pile and column foundations to generate more stiffness. They generate stiffness by forcing the piles to move as a group rather than individually and by providing fixity (i.e., resistance to rotation) at the ends of the piles. Typically, they extend in both directions and are usually made of reinforced concrete. The mix design, the amount and placement of reinforcement, the cover, and the curing process are important parameters in optimizing durability. To reduce the effect of erosion and scour on foundations, grade beams must be designed to be self-supporting foundation elements. The supporting piers should be designed to carry the weight of the grade beams and resist all loads transferred to the piers. In V Zones, grade beams must be used only for lateral support of the piles. If, during construction, the floor is made monolithic with the grade beams, the bottom of the beams become the lowest horizontal structural member. This elevation must be at or above the BFE. If grade beams are used with wood piles, the possibility of rot occurring must be considered when designing the connection between the grade beam and the pile. The connection must not encourage water retention. The maximum bending moment in the piles occurs at the grade beams, and decay caused by water retention at critical points in the piles could induce failure under high wind or flood forces. 3 FOUNDATION DESIGN LOADS 3- Building on strong and safe foundations Design methods can be used to design a building. For this manual, all of the calculations, analyses, and load combinations presented are based on ASD. The use of Strength Design methods will require the designer to modify the design values presented in this manual to accommodate Strength Design concepts. Assumptions utilized in this document can be found in Appendix C. 3.1 Wind Loads Wind loads on a building structure are calculated using the methodology presented in ASCE 7-02, Minimum Design Loads for Buildings and Other Structures. This document is the wind standard referenced by the 2003 editions of the IBC and IRC. Equations used to calculate wind loads are presented in Appendix D. The most important variable in calculating wind load is the design wind speed. Design wind speed can be obtained from the local building official or the ASCE 7-02 wind speed map (see Figure 3-1). The speeds shown in this figure are 3-second gust speeds for Exposure Category C at a 33-foot (10-meter) height. ASCE 7-02 includes scaling factors for other exposures and heights. ASCE 7-02 specifies wind loads for structural components known as a Main Wind Force Resisting System (MWFRS). The foundation designs developed for this manual are based on MWFRS pressures calculated for Exposure Category C, the category with the highest anticipated wind loads for land-based structures. ASCE 7-02 also specifies wind loads for components and cladding (C&C). Components and cladding are considered part of the building envelope, and ASCE 7-02 requires C&C to be designed to resist higher wind pressures than MWFRS. FOUNDATION DESIGN LOADS 3 3- 3.2 Flood Loads This manual develops in more detail flood load calculations and incorporates the methodology presented in ASCE 7-02. Although wind loads can directly affect a structure and dictate the actual foundation design, the foundation is more affected by flood loads. ASCE 24 discusses floodproof construction. Loads developed in ASCE 24 come directly from ASCE 7-02, which is what the designs presented herein are based upon. The effects of flood loads on buildings can be exacerbated by storm-induced erosion and localized scour, and by long-term erosion. Erosion and scour lower the ground surface around foundation members and can cause the loss of load-bearing capacity and resistance to lateral and uplift loads. Erosion and scour also increase flood depths and, therefore, increase depth dependent flood loads. Figure 3-1. Wind speed (in mph) in the U.S. Gulf Coast area Source: ASCE 7-02 3.2.1 Design Flood and Design Flood Elevation (DFE) The design flood is defined by ASCE 7-02 as the greater of the following two flood events: 1. Base flood, affecting those areas identified as SFHAs on the community’s FIRM, or 2. The flood corresponding to the area designated as a flood hazard area on a community’s flood hazard map or otherwise legally designated. The DFE is defined as the elevation of the design flood, including wave height and freeboard, relative to the datum specified on a community’s flood hazard map. Figure 3-2 shows the parameters that determine or are affected by flood depth. Figure 3-2. Parameters that determine or are affected by flood depth Source: COastal COnstruction manual (FEMA 55) 3.2.2 Design Stillwater Flood Depth (ds) Design stillwater flood depth (ds) is the vertical distance between the eroded ground elevation and the stillwater flood elevation associated with the design flood. Determining the maximum design stillwater flood depth over the life of a building is the single most important flood load calculation that will be made; nearly all other coastal flood load parameters or calculations (e.g., hydrostatic load, design flood velocity, hydrodynamic load, design wave height, DFE, debris impact load, local scour depth) depend directly or indirectly on the design stillwater flood depth. The design stillwater flood depth (ds) is defined as ds = Esw – GS Where ds = Design stillwater flood depth (ft) Esw = Design stillwater flood elevation (ft) above the datum (e.g., National Geodetic Vertical Datum [NGVD], North American Vertical Datum [NAVD]), including wave setup effects GS = Lowest eroded ground elevation above datum (ft), adjacent to building, including the effects of localized sour around pilings GS is not the lowest existing pre-flood ground surface; it is the lowest ground surface that will result from long-term erosion and the amount of erosion expected to occur during a design flood, excluding local scour effects. The process for determining GS is described in Chapter 7 of FEMA 55. Values for Esw are not shown on a FIRM, but they are given in the Flood Insurance Study (FIS) report, which is produced in conjunction with the FIRM for a community. FIS reports are usually available from community officials, from NFIP State Coordinating Agencies, and on the web at the FEMA Map Service Center (http://store.msc.fema.gov). Some states have FIS reports available on their individual web sites. 3.2.3 Design Wave Height (Hb) The design wave height at a coastal building site will be one of the most important design parameters. Therefore, unless detailed analysis shows that natural or manmade obstructions will protect the site during a design event, wave heights at a site will be calculated from Equation 5-2 of ASCE 7-02 as the heights of depth-limited breaking waves (Hb), which are equivalent to 0.78 times the design stillwater flood depth: Hb = 0.78ds Note: 70 percent of the breaking wave height (0.7Hb) lies above the stillwater flood level. 3.2.4 Design Flood Velocity (V) Estimating design flood velocities in coastal flood hazard areas is subject to considerable uncertainty. Little reliable historical information exists concerning the velocity of floodwaters during coastal flood events. The direction and velocity of floodwaters can vary significantly throughout a coastal flood event, approaching a site from one direction during the beginning of the flood event before shifting to another (or several directions). Floodwaters can inundate some low-lying coastal sites from both the front (e.g., ocean) and the back (e.g., bay, sound, river). In a similar manner, flow velocities can vary from close to zero to high velocities during a single flood event. For these reasons, flood velocities should be estimated conservatively by assuming that floodwaters can approach from the most critical direction and that flow velocities can be high. For design purposes, the Commentary of ASCE7-02 suggested a range of flood velocities from: V = ds ÷ t (expected lower bound) to V = (gds)0.5 (expected upper bound) Where ds = Design stillwater flood depth t = Time (1 second) g = Gravitational constant (32.2 ft/sec2) Factors that should be considered before selecting the upper- or lower-bound flood velocity for design include: n Flood zonen Topography and slopen Distance from the source of floodingn Proximity to other buildings or obstructions The upper bound should be taken as the design flood velocity if the building site is near the flood source, in a V Zone, in an AO Zone adjacent to a V Zone, in an A Zone subject to velocity flow and wave action, steeply sloping, or adjacent to other buildings or obstructions that will confine floodwaters and accelerate flood velocities. The lower bound is a more appropriate design flood velocity if the site is distant from the flood source, in an A Zone, flat or gently sloping, or unaffected by other buildings or obstructions. 3.3 Hydrostatic Loads Hydrostatic loads occur when standing or slowly moving water comes into contact with a building or building component. These loads can act laterally (pressure) or vertically (buoyancy). Lateral hydrostatic forces are generally not sufficient to cause deflection or displacement of a building or building component unless there is a substantial difference in water elevation on opposite sides of the building or component; therefore, the NFIP requires that floodwater openings be provided in vertical walls that form an enclosed space below the BFE for a building in an A Zone. Lateral hydrostatic force is calculated by the following: fstat = ½ . ds2 Where fstat = Hydrostatic force per unit width (lb/ft) resulting from flooding against vertical element . = Specific weight of water (62.4 lb/ft3 for freshwater and 64 lb/ft3 for saltwater) Vertical hydrostatic forces during design flood conditions are not generally a concern for properly constructed and elevated coastal buildings. Buoyant or flotation forces on a building can be of concern if the actual stillwater flood depth exceeds the design stillwater flood depth. Vertical (buoyancy) hydrostatic force is calculated by the following: FBuoy = . (Vol) Where FBuoy = vertical hydrostatic force (lb) resulting from the displacement of a given volume of floodwater Vol = volume of floodwater displaced by a submerged object (ft3) = displaced area x depth of flooding Buoyant force acting on an object must be resisted by the weight of the object and any other opposing force (e.g., anchorage forces) resisting flotation. In the case of a building, the live load on floors should not be counted on to resist buoyant forces. 3.4 Wave Loads Calculating wave loads requires information about expected wave heights. For the purposes of this manual, the calculations will be limited by water depths at the site of interest. Wave forces can be separated into four categories: n Non-breaking waves (can usually be computed as hydrostatic forces against walls and hydrodynamic forces against piles) n Breaking waves (short duration but large magnitude forces against walls and piles) n Broken waves (similar to hydrodynamic forces caused by flowing or surging water) n Uplift (often caused by wave runup, deflection, or peaking against the underside of horizontal surfaces) Of these four categories, the forces from breaking waves are the largest and produce the most severe loads. Therefore, it is strongly recommended that the breaking wave load be used as the design wave load. Two breaking wave loading conditions are of interest in residential construction: waves breaking on small-diameter vertical elements below the DFE (e.g., piles, columns in the foundation of a building in a V Zone) and waves breaking against vertical walls below the DFE (e.g., solid foundation walls in A Zones, breakaway walls in V Zones). 3.4.1 Breaking Wave Loads on Vertical Piles The breaking wave load (Fbrkp) on a pile can be assumed to act at the stillwater flood level and is calculated by Equation 5-4 from ASCE 7-02: Fbrkp = (1/2)CD.DHb2 Where Fbrkp = Net wave force (lb) CD = Coefficient of drag for breaking waves = 1.75 for round piles or column, and 2.25 for square piles or columns . = Specific weight of water (lb/ft3) D = Pile or column diameter (ft) for circular section. For a square pile or column, 1.4 times the width of the pile or column (ft). Hb = Breaking wave height (ft) 3.4.2 Breaking Wave Loads on Vertical Walls The net force resulting from a normally incident breaking wave (depth limited in size, with Hb = 0.78ds) acting on a rigid vertical wall, can be calculated by Equation 5-6 from ASCE 7-02: Fbrkw = 1.1Cp.ds2 + 2.4.ds2 Where Fbrkw = net breaking wave force per unit length of structure (lb/ft) acting near the stillwater flood elevation Cp = Dynamic pressure coefficient (1.6 < Cp < 3.5) (see Table 3-1) Table 3-1. Building Category and Corresponding Dynamic Pressure Coefficient (Cp) Building Category Cp I – Buildings and other structures that represent a low hazard to human life in the event of a failure 1.6 II – Buildings not in Category I, III, and IV 2.8 III – Buildings and other structures that represent a substantial hazard to human life in the event of a failure 3.2 IV – Buildings and other structures designated as essential facilities 3.5 Source: ASCE 7-02 . = Specific weight of water (lb/ft3) ds = Design stillwater flood depth (ft) at base of building where the wave breaks This formula assumes the following: n The vertical wall causes a reflected or standing wave against the seaward side of the wall with the crest of the wave, reaching a height of 1.2ds above the design stillwater flood elevation, andn The space behind the vertical wall is dry, with no fluid balancing the static component of the wave force on the outside of the wall (see Figure 3-3). If free-standing water exists behind the wall (see Figure 3-4), a portion of the hydrostatic component of the wave pressure and force disappears and the net force can be computed using Equation 5-7 from ASCE 7-02: Fbrkw = 1.1Cp.ds2 + 1.9.ds2 Post-storm damage inspections show that breaking wave loads have destroyed virtually all wood- frame or unreinforced masonry walls below the wave crest elevation; only highly engineered, massive structural elements are capable of withstanding breaking wave loads. Damaging wave pressures and loads can be generated by waves much lower than the 3-foot wave currently used by FEMA to distinguish between A Zones and V Zones. Figure 3-3. Normally incident breaking wave pressures against a vertical wall (space behind vertical wall is dry) Source: ASCE 7-02 Figure 3-4. Normally incident breaking wave pressures against a vertical wall (stillwater level equal on both sides of wall) Source: ASCE 7-02 3.5 Hydrodynamic Loads Water flowing around a building (or a structural element or other object) imposes additional loads on the building. The loads (which are a function of flow velocity and structural geometry) include frontal impact on the upstream face, drag along the sides, and suction on the downstream side. This manual assumes that the velocity of the floodwaters is constant (i.e., steady state flow). One of the most difficult steps in quantifying loads imposed by moving water is determining the expected flood velocity. Refer to Section 3.2.4 for guidance concerning design flood velocities. The following equation from FEMA 55 can be used to calculate the hydrodynamic load from flows with velocity greater than 10 ft/sec: Fdyn = ½Cd .V2A Where Fdyn = Hydrodynamic force (lb) acting at the stillwater mid-depth (halfway between the stillwater elevation and the eroded ground surface) Cd = Drag coefficient (recommended values are 2.0 for square or rectangular piles and 1.2 for round piles) . = Mass density of fluid (1.94 slugs/ft3 for freshwater and 1.99 slugs/ft3 for saltwater) V = Velocity of water (ft/sec) A = Surface area of obstruction normal to flow (ft2) Note that the use of this formula will provide the total force against a building of a given impacted surface area (A). Dividing the total force by either length or width would yield a force per unit length; dividing by “A” would yield a force per unit area. The drag coefficient used in the previously stated equations is a function of the shape of the object around which flow is directed. If the object is something other than a round, square, or rectangular pile, the drag coefficient can be determined using Table 3-2. Table 3-2. Drag Coefficient Based on Width to Depth Ratio Width to Depth Ratio (w/ds or w/h) Drag Coefficient (Cd) 1 to 12 1.25 13 to 20 1.30 21 to 32 1.40 33 to 40 1.50 41 to 80 1.75 81 to 120 1.80 >120 2.00 Note: “h” refers to the height of an object completely immersed in water. Source: FEMA 55 Flow around a building or building component will also create flow-perpendicular forces (lift forces). If the building component is rigid, lift forces can be assumed to be small. But if the building component is not rigid, lift forces can be greater than drag forces. The formula for lift force is similar to the formula for hydrodynamic force except that the drag coefficient (Cd) is replaced with the lift coefficient (Cl). For the purposes of this manual, the foundations of coastal residential buildings can be considered rigid, and hydrodynamic lift forces can therefore be ignored. 3.6 Debris Impact Loads Debris or impact loads are imposed on a building by objects carried by moving water. The magnitude of these loads is very difficult to predict, yet some reasonable allowance must be made for them. The loads are influenced by where the building is located in the potential debris stream: n Immediately adjacent to or downstream from another buildingn Downstream from large flotable objects (e.g., exposed or minimally covered storage tanks) n Among closely spaced buildings The following equation to calculate the magnitude of impact load is provided in the Commentary of ASCE 7-02: Fi = (pWVCiCoCDCBRmax) ÷ (2g.t) Where Fi = Impact force acting at the stillwater level (lb) p = 3.14 W = Weight of debris (lb), suggest using 1,000 if no site-specific information is available V = Velocity of object (assume equal to velocity of water) (ft/sec) Ci = Importance coefficient (see Table C5.3 of ASCE 7-02) Co = Orientation coefficient = 0.8 CD = Depth coefficient (see Table C5.5 and Figure C5-3 of ASCE 7-02) CB = Blockage coefficient (see Table C5.5 and Figure 5-4 of ASCE 7-02) Rmax= Maximum response ratio for impulsive load (see Table C5.6 of ASCE 7-02) g = Gravitational constant (32.2 ft/sec2) .t = Duration of impact (sec) When the C coefficients and Rmax are set to 1.0, the above equation reduces to Fi = (pWV) ÷ (2g.t) This equation is very similar to the equation provided in ASCE 7-98 and FEMA 55. The only difference is the p/2 term, which results from the half-sine form of the impulse load. The following uncertainties must be quantified before the impact of debris loading on the building can be determined using the above equation: n Size, shape, and weight (W) of the waterborne objectn Flood velocity (V) n Velocity of the object compared to the flood velocityn Portion of the building that will be struck and most vulnerable to collapsingn Duration of the impact (t) Once floodborne debris impact loads have been quantified, decisions must be made on how to apply them to the foundation and how to design foundation elements to resist them. For open foundations, the Coastal Construction Manual (FEMA 55) advises applying impact loading to a corner or critical column or piling concurrently with other flood loads (see Coastal Construction Manual, Table 11-6). For closed foundations (which are not recommended in Coastal A Zones and are not allowed in V Zones), the Coastal Construction Manual advises that the designer assume that one corner of the foundation will be destroyed by debris and recommends the foundation and the structure above be designed to contain redundancy to allow load redistribution to prevent collapse or localized failure. The following should be considered in determining debris impact loads: Size, shape, and weight of the debris. It is recommended that, in the absence of information about the nature of the potential debris, a weight of 1,000 pounds be used for the debris weight (W). Objects of this weight could include portions of damaged buildings, utility poles, portions of previously embedded piles, and empty storage tanks. Debris velocity. Flood velocity can be approximated by one of the equations discussed in Section 3.2.4. For the calculation of debris loads, the velocity of the waterborne object is assumed to be the same as the flood velocity. Note that, although this assumption may be accurate for small objects, it will overstate debris velocities for large objects (e.g., trees, logs, pier pilings). The Commentary of ASCE 7-02 provides guidance on estimating debris velocities for large debris. Portion of building to be struck. The object is assumed to be at or near the water surface level when it strikes the building. Therefore, the object is assumed to strike the building at the stillwater flood level. Duration of impact. Uncertainty about the duration of impact (.t) (the time from initial impact, through the maximum deflection caused by the impact, to the time the object leaves) is the most likely cause of error in the calculation of debris impact loads. ASCE 7-02 showed that measured impact duration (from initial impact to time of maximum force) from laboratory tests varied from 0.01 to 0.05 second. The ASCE 7-02 recommended value for .t is 0.03 second. 3.7 Localized Scour Waves and currents during coastal flood conditions are capable of creating turbulence around foundation elements and causing localized scour. Determining potential scour is critical in designing coastal foundations to ensure that failure during and after flooding does not occur as a result of the loss in either bearing capacity or anchoring resistance around the posts, piles, piers, columns, footings, or walls. Localized scour determinations will require knowledge of the flood depth, flow conditions, soil characteristics, and foundation type. NOTE: The method for determining debris impact loads in ASCE 7-02 was developed for riverine impact loads and has not been evaluated for coastal debris that may impact a building over several wave cycles. Although these impact loads are very large but of short duration, a structural engineer should be consulted to determine the structural response to the short load duration (0.03 second recommended). In some locations, soil at or below the ground surface can be resistant to localized scour, and scour depths calculated below will be excessive. In instances where the designer believes the soil at a site will be scour-resistant, a geotechnical engineer should be consulted before calculated scour depths are reduced. 3.7.1 Localized Scour Around Vertical Piles The methods for calculating localized scour (Smax) in coastal areas have been largely based on empirical evidence gathered after storms. Much of the evidence gathered suggests that localized scour depths around piles and other thin vertical members are approximately equal to 1.0 to 1.5 times the pile diameter. Figure 3-5 illustrates localized scour at a pile, with and without a scour-resistant terminating stratum. Currently, there is no design guidance in ASCE 7-02 on how to calculate scour. Localized scour around a vertical pile or similar foundation element should be calculated with the following formula as given in FEMA 55: Smax = 2.0a Where Smax = Maximum localized scour depth (ft) a = Diameter of a round foundation element or the maximum diagonal cross-section dimension for a rectangular element (ft) 3.7.2 Localized Scour Around Vertical Walls and Enclosures Localized scour around vertical walls and enclosed areas (e.g., typical A Zone construction) can be greater than that around vertical piles, and should be estimated using Table 3-3. Figure 3-5. Scour at vertical foundation member stopped by underlying scour-resistant stratum Source: COastal COnstruction manual (FEMA 55) Table 3-3. Local Scour Depth as a Function of Soil Type Soil Type Expected Depth (% of ds) Loose sand 80 Dense sand 50 Soft silt 50 Stiff silt 25 Soft clay 25 Stiff clay 10 Source: FEMA 55 3.8 Flood Load Combinations Load combinations (including those for flood loads) are given in ASCE 7-02, Sections 2.3.2 and 2.3.3 for strength design and Sections 2.4.1 and 2.4.2 for allowable stress design. The basic load combinations are: Allowable Stress Design (1) D + F (2) D + H + F + L + T (3) D + H + F + (Lr or S or R) (4) D + H + F + 0.75(L + T) + 0.75(Lr or S or R) (5) D + H + F + (W or 0.7E) (6) D + H + F + 0.75(W or 0.7E) + 0.75L + 1.5Fa + 0.75(Lr or S or R) (7) 0.6D + W + H (8) 0.6D + 0.7 E + H Strength Design (1) 1.4 (D + F) (2) 1.2 (D + F + T) + 1.6(L + H) + 0.5(Lr or S or R) (3) 1.2D + 1.6(Lr or S or R) + (L or 0.8W) (4) 1.2D + 1.6W + L + 0.5(Lr or S or R) (5) 1.2D + 1.0E + L + 0.2S (6) 0.9D + 1.6W + 1.6H (7) 0.9D + 1.0E + 1.6H For structures located in V or Coastal A Zones: Allowable Stress Design Load combinations 5, 6, and 7 shall be replaced with the following: (5) D + H + F + 1.5Fa + W (6) D + H + F + 0.75W + 0.75L + 1.5Fa + 0.75(Lr or S or R) (7) 0.6D + W + H + 1.5Fa Strength Design Load combinations 4 and 6 given in ASCE 7-02 Section 2.3.1 shall be replaced with the following: (4) 1.2D + 1.6W + 2.0Fa + L + 0.5(Lr or S or R) (6) 0.9D + 1.6W + 2.0 Fa + 1.6H Where D = Dead Load W = Wind Load E = Earthquake Load Fa = Flood Load F = Load due to fluids with well defined pressures and maximum heights L = Live Load Lr = Roof Live Load S = Snow Load R = Rain Load H = Lateral Earth Pressure Flood loads were included in the load combinations to account for the strong correlation between flood and winds in hurricane-prone regions that run along the Gulf of Mexico and the Atlantic Coast. In non-Coastal A Zones, for Allowable Stress Design, replace the 1.5Fa with 0.75Fa in load combinations 5, 6, and 7 given above. For Strength Design, replace coefficients W and Fa in equations 4 and 6 above with 0.8 and 1.0, respectively. Designers should be aware that not all of the flood loads will act at certain locations or against certain building types. Table 3-4 provides guidance to designers for the calculation of appropriate flood loads in V Zones and Coastal A Zones (non-Coastal A Zone flood load combinations are shown for comparison). The floodplain management regulations enacted by communities that participate in the NFIP prohibit the construction of solid perimeter wall foundations in V Zones, but allow such foundations in A Zones. Therefore, the designer should assume that breaking waves will impact piles in V Zones and walls in A Zones. It is generally unrealistic to assume that impact loads will occur on all piles at the same time as breaking wave loads; therefore, this manual recommends that impact loads be evaluated for strategic locations such as a building corner. Table 3-4. Selection of Flood Load Combinations for Design Case 1 Pile or Open Foundation in V Zone (Required) Fbrkp (on all piles) + Fi (on one corner or critical pile only) or Fbrkp (on front row of piles only) + Fdyn (on all piles but front row) +Fi (on one corner or critical pile only) Case 2 Pile or Open Foundation in Coastal Z Zone (Recommended) Fbrkp (on all piles) + Fi (on one corner or critical pile only) or Fbrkp (on front row of piles only) + Fdyn (on all piles but front row) +Fi (on one corner or critical pile only) Case 3 Solid (Wall) Foundation in Coastal A Zone (NOT Recommended) Fbrkp (on walls facing shoreline, including hydrostatic component) + Fdyn; assume one corner is destroyed by debris, and design in redundancy Case 4 Solid (Wall) Foundation in Non-Coastal A Zone (Shown for Comparison) Fsta + Fdyn Source: COastal COnStruction manual (FEMA 55) RECOMMENDED RESIDENTIAL CONSTRUCTION FOR THE GULF COAST 4. Overview of Recommended Foundation Types and Construction for the Gulf Coast Chapters 1 through 3 discussed foundation design loads and calculations and how these issues can be influenced by coastal natural hazards. This chapter will tie all of these issues together with a discussion of foundation types and methods of constructing a foundation for a residential structure. 4- 4 Overview of Recommended Foundation Types and Construction for the Gulf Coast 4- Building on strong and safe foundations 4.1 Critical Factors Affecting Foundation Design Foundation construction types are dependent upon the following critical factors: n Design wind speedn Elevation height required by the BFE and local ordinancesn Flood zone n Soil parameters Soil parameters are very important but, for the purpose of creating standardized foundation designs in this report, soil parameters have been fixed. This section will only discuss the first three critical factors mentioned above. 4.1.1 Wind Speed A design wind speed is a factor that determines the foundation size and strength (see also Section 1.1). The wind speed map shown in Figure 3-1 shows the design winds along most of the Mississippi and Louisiana Gulf Coast areas to be between 120 and 150 mph. To determine forces on the building and foundation, the wind speed is critical. Wind speed creates wind pressures that act upon the building. These pressures are proportional to the square of the wind speed, so a doubling of the wind speed increases the wind pressure by a factor of four. The pressure applied to an area of the building will develop forces that must be resisted. To transfer these forces from the building to the foundation, properly designed load paths are required. For the foundation to be properly designed, all forces including uplift, compression, and lateral must be taken into account. 4.1.2 Elevation The required height of the foundation depends on three factors: the DFE, the site elevation, and the flood zone. The flood zone dictates whether the lowest habitable finished floor must be placed at the DFE or, in the case of homes in the V Zone, the bottom of the lowest horizontal member must be placed at the DFE. While not required by the NFIP, V Zone criteria are recommended for Coastal A Zones. Stated mathematically, H = DFE – G + Erosion or H = BFE – G + Erosion + Freeboard Where H = Required foundation height (in ft) DFE = Design Flood Elevation BFE = Base Flood Elevation Overview of Recommended Foundation Types and Construction for the Gulf Coast 4 4- G = Non-eroded ground elevation Erosion = Short-term plus long-term erosion Freeboard = Locally adopted or owner desired freeboard The height to which a home should be elevated is one of the key factors in determining which pre-engineered foundation to use. Elevation height is dependent upon several factors, including the BFE, local ordinances requiring freeboard, and the desire of the homeowner to elevate the lowest horizontal structural member above the BFE (see also Chapter 2). This manual provides designs for closed foundations up to 8 feet above ground level and open foundations up to 15 feet above ground level. Custom designs can be developed for open and closed foundations to position the homes above those elevation levels. Foundations for homes that need to be elevated higher than 15 feet should be designed by a licensed professional engineer. 4.1.3 Construction Materials The use of flood-resistant materials below the BFE is also covered in FEMA NFIP Technical Bulletin 2 and FEMA 499 Fact Sheet No. 8 (see also Appendix F). This manual will cover the materials used in masonry and concrete foundation construction, and field preservative treatment for wood. 4.1.3.1 Masonry Foundation Construction The combination of high winds, moisture, and salt-laden air creates a damaging recipe for masonry construction. All three can penetrate the tiniest cracks or openings in the masonry joints. This can corrode reinforcement, weaken the bond between the mortar and the brick, and create fissures in the mortar. Moisture resistance is highly influenced by the quality of the materials and the workmanship. 4.1.3.2 Concrete Foundation Construction Cast-in-place concrete elements in coastal environments should be constructed with 3 inches or more of concrete cover over the reinforcing bars. The concrete cover physically protects the reinforcing bars from corrosion. However, if salt water penetrates the concrete cover and reaches the reinforcing steel, the concrete alkalinity is reduced by the salt chloride, thereby corroding the steel. As the corrosion forms, it expands and cracks the concrete, allowing the additional entry of water and further corrosion. Eventually, this process weakens the concrete structural element and its load carrying capacity. Alternatively, epoxy-coated reinforcing steel can be used if properly handled, stored, and placed. Epoxy-coated steel, however, requires more sophisticated construction techniques and more highly trained contractors that are not usually involved with residential construction. Concrete mix used in coastal areas must be designed for durability. The first step in this process is to start with the mix design. The American Concrete Institute (ACI) 318 manual recommends that a maximum water-cement ratio by weight of 0.40 and a minimum compressive strength of 4,000 pounds per square inch (psi) be used for concrete used in coastal environments. Since the amount of water in a concrete mix largely determines the amount that concrete will shrink and promote unwanted cracks, the water-cement ratio of the concrete mix is a critical parameter in promoting concrete durability. Adding more water to the mix to improve the workability increases the potential for cracking in the concrete and can severely affect its durability. Another way to improve the durability of a concrete mix is with ideal mix proportions. Concrete mixes typically consist of a mixture of sand, aggregate, and cement. How these elements are proportioned is as critical as the water-cement ratio. The sand should be clean and free of contaminants. The aggregate should be washed and graded. The type of aggregate is also very important. Recent research has shown that certain types of gravel do not promote a tight bond with the paste. The builder or contractor should consult expert advice prior to specifying the concrete mix. Addition of admixtures such as pozzolans (fly ash) is recommended for concrete construction along the coast. Fly ash when introduced in concrete mix has benefits such as better workability and increased resistance to sulfates and chlorates, thus reducing corrosion from attacking the steel reinforcing. 4.1.3.3 Field Preservative Treatment for Wood Members In order to properly connect the pile foundation to the floor framing system, making field cuts, notches, and boring holes are some of the activities associated with construction. Since pressure-preservative-treated piles, timbers, and lumber are used for many purposes in coastal construction, the interior, untreated parts of the wood are exposed to possible decay and infestation. Although treatments applied in the field are much less effective than factory treatments, the potential for decay can be minimized. The American Wood Preservers’ Association (AWPA) standard Care of Pressure-Treated Wood Products (AWPA 1991) describes field treatment procedures and field cutting restrictions for poles, piles, and sawn lumber. Field application of preservatives should always be done in accordance with instructions on the label. When detailed instructions are not provided, dip soaking for at least 3 minutes can be considered effective for field applications. When this is impractical, treatment may be done by thoroughly brushing or spraying the exposed area. It should be noted that the material is more absorptive at the end of a member, or end grains, than it is for the sides or side grains. To safeguard against decay in bored holes, the holes should be poured full of preservative. If the hole passes through a check (such as a shrinkage crack caused by drying), it will be necessary to brush the hole; otherwise, the preservative would run into the check instead of saturating the hole. Waterborne arsenicals, pentachlorophenol, and creosote are unacceptable for field applications. Copper napthenate is the most widely used field treatment. Its deep green color may be objectionable, but the wood can be painted with alkyd paints in dark colors after extended drying. Zinc napthenate is a clear alternative to copper napthenate. However, it is not quite as effective in preventing insect infestation, and it should not be painted with latex paints. Tributyltin oxide (TBTO) is available, but should not be used in or near marine environments, because the leachates are toxic to aquatic organisms. Sodium borate is also available, but it does not readily penetrate dry wood and it rapidly leaches out when water is present. Therefore, sodium borate is not recommended. 4.1.4 Foundation Design Loads To provide flexibility in the home designs, tension connections have been specified between the tops of all wood piles and the grade beams. Depending on the location of shear walls, shear wall openings, and the orientation of floor and roof framing, some wood piles may not experience tension forces. Design professionals can analyze the elevated structure to identify compression only pilings to reduce construction costs. For foundation design and example calculations, see Appendix D. Figure 4-1 illustrates design loads acting on a column. The reactions at the base of the elevated structure used in the foundation designs are presented in Tables 4-1a (one-story) and 4-1b (two-story). These reactions are the controlling forces for the range of building weights and dimensions listed in Appendix A and shown in Figure 2 of the Introduction. Design reactions have been included for the various design wind speeds and various building elevations above exterior grade. ASCE 7-02 Load Combination 4 (D + 0.75L + 0.75Lr) controls for gravity loading and Load Combination 7 controls for uplift and lateral loads. Load Combination 7 is 0.6D + W + 0.75Fa in non-Coastal A Zones and 0.6D + W + 1.5Fa in Coastal A and V Zones. Refer to Section 3.8 for the list of flood load combinations. Figure 4-1. Design loads acting on a column Loads on the foundation elements themselves are more difficult to tabulate since they depend on the foundation style (open or enclosed), foundation dimensions, and foundation height. Table 4-2 provides reactions for the 18-inch square columns used in most of the open foundation designs. Table 4-1a. Design Perimeter Wall Reactions (lb/lf) for One-Story Elevated Homes (Note: Reactions are taken at the base of the elevated home/top of the foundation element.) V 120 mph 130 mph 140 mph 150 mph (All V) H Horiz Vert Horiz Vert Horiz Vert Horiz Vert Gravity 5 ft 770 -175 903 -259 1,048 -350 1,203 -448 1,172 6 ft 770 -175 903 -259 1,048 -350 1,203 -448 1,172 7 ft 770 -175 903 -259 1,048 -350 1,203 -448 1,172 8 ft 804 -202 944 -291 1,095 -388 1,257 -490 1,172 10 ft 804 -202 944 -291 1,095 -388 1,257 -490 1,172 12 ft 804 -202 944 -291 1,095 -388 1,257 -490 1,172 14 ft 832 -224 977 -317 1,133 -417 1,300 -525 1,172 15 ft 843 -226 989 -319 1,147 -419 1,317 -527 1,172 lb = pound lf = linear foot V = wind speed H = height of foundation above grade Table 4-1b. Design Perimeter Wall Reactions (lb/lf) for Two-Story Elevated Homes (Note: Reactions are taken at the base of the elevated home/top of the foundation element.) V 120 mph 130 mph 140 mph 150 mph (All V) H Horiz Vert Horiz Vert Horiz Vert Horiz Vert Gravity 5 ft 1,149 -145 1,348 -255 1,564 -374 1,795 -502 1,608 6 ft 1,149 -145 1,348 -255 1,564 -374 1,795 -502 1,608 7 ft 1,149 -145 1,348 -255 1,564 -374 1,795 -502 1,608 8 ft 1,182 -168 1,387 -282 1,609 -406 1,847 -539 1,608 10 ft 1,191 -171 1,397 -286 1,629 -410 1,860 -543 1,608 12 ft 1,191 -171 1,397 -286 1,620 -410 1,860 -543 1,608 14 ft 1,191 -171 1,397 -286 1,620 -410 1,860 -543 1,608 15 ft 1,210 -175 1,420 -291 1,647 -416 1,890 -550 1,608 lb = pound lf = linear foot V = wind speed H = height of foundation above grade Table 4-2. Flood Forces (in pounds) on an 18-inch Square Column Flood Depth Hydrodynamic Breaking Wave Impact Buoyancy 5 ft 1,000 684 3,165 465 6 ft 1,440 985 3,476 577 7 ft 1,960 1,340 3,745 650 8 ft 2,560 1,750 4,004 743 10 ft 4,001 2,735 4,476 939 12 ft 5,761 3,938 4,903 1,115 14 ft 7,841 5,360 5,296 1,300 15 ft 9,002 6,155 5,482 1,394 4.2 Recommended Foundation Types for the Gulf Coast Table 4-3 provides five open (deep and shallow) foundation types and two closed foundations discussed in this manual. Appendix A provides the foundation design drawings for the cases specified. Table 4-3. Recommended Foundation Types Based on Zone Foundation Case V Zones A Zones in Coastal Areas Coastal A Zone A Zone Open Foundation (deep) Timber pile A 4 4 4 Steel pipe pile with concrete column and grade beam B 4 4 4 Timber pile with concrete column and grade beam C 4 4 4 Open Foundation (shallow) Concrete column and grade beam D NR 4 4 Concrete column and grade beam with slab G NR 4 4 Closed Foundation (shallow) Reinforced masonry – crawlspace E 8 NR 4 Reinforced masonry – stem wall F 8 NR 4 4 = Acceptable NR = Not Recommended 8 = Not Permitted The foundation designs contained in this manual are based on soils having a bearing capacity of 1,500 pounds per square foot (psf). The 1,500-psf bearing capacity value corresponds to the presumptive value contained in the 2003 IBC for cohesive soil. Cohesive soils are fine-grained soils (or soils with a high clay content) with cohesive strength. These types of soils include clay, sandy clay, silty clay, clayey silt, silt, and sandy silt. The size of the perimeter footings and grade beams are generally not controlled by bearing capacity (uplift and lateral loads typically control footing size and grade beam dimensions). Refining the designs for soils with greater bearing capacities may not significantly reduce construction costs. However, the size of the interior pad footings for the crawlspace foundation (Table 4-3, E: Closed Foundation, Reinforced Masonry - Crawlspace) depends greatly on the soil’s bearing capacity. Design refinements can reduce footing sizes in areas where soils have greater bearing capacities. The following discussion of the foundation designs listed in Table 4- 3 is also presented in Appendix A. Figures 4-2 through 4-8 are based on Appendix A. 4.2.1 Open Foundation: Timber Pile (Case A) This pre-engineered, timber pile foundation uses conventional, tapered, treated piles and steel rod bracing to support the elevated structure. No concrete, masonry, or reinforcing steel is needed (see Figure 4-2). Often called a “stilt” foundation, the driven timber pile system is suitable for moderate elevations if the homebuilder prefers to minimize the number of different construction trades used. Once the piles are driven, the wood guides and floor system are attached to the piles; the remainder of the house is constructed off the floor platform. The recommended design for Case A that is presented in this manual accommodates home elevations up to 10 feet above grade. With customized designs and longer piles, the designs can be modified to achieve higher elevations. However, elevations greater than 10 feet will likely be prevented by pile availability, the pile strength required to resist lateral forces, and the pile embedment required to resist scour and erosion. A construction approach that can improve performance is to extend the piles above the first floor diaphragm to the second floor or roof diaphragm. Doing so allows the foundation and the elevated home to function more like a single, integrated structural frame. Extending the piles stiffens the structure, reduces stresses in the pilings, and reduces lateral deflections. Post disaster assessments of pile supported homes indicate that extending piles in this fashion improves survivability. Licensed professional engineers should be consulted to analyze the pile foundations and design the appropriate connections. One drawback of the timber pile system is the exposure of the piles to floodborne debris. During a hurricane event, individual piles can be damaged or destroyed by large, floating debris. With the home in place, damaged piles are difficult to replace. Two separate ways of addressing this potential problem is to use piles with a diameter larger than is called for in the foundation design or to use a greater number of piles to increase structural redundancy. 4.2.2 Open Foundation: Steel Pipe Pile with Concrete Column and Grade Beam (Case B) This foundation incorporates open-ended steel pipe piles; this style is somewhat unique to the Gulf Coast region where the prevalence of steel pipe pilings used to support oil platforms has created local sources for these piles. Like treated wood piles, steel pipe piles are driven but have the advantage of greater bending strength and load carrying capacity (see Figure 4-3). The open steel pipe pile foundation is resistant to the effects of erosion and scour. The grade beam can be undermined by scour without compromising the entire foundation system. Figure 4-2. Profile of Case A foundation type (see Appendix A for additional drawings) for The number of piles required depends on local soil conditions. Like other soil dependent foundation designs, consideration should be given to performing soil tests on the site so the foundation design can be optimized. With guidance from engineers, the open-ended steel pipe pile foundation can be designed for higher elevations. Additional piles can be driven for increased resistance to lateral forces, and columns can be made larger and stronger to resist the increased bending moments that occur where the columns join the grade beam. Because only a certain amount of steel can be installed to a given cross-section of concrete before the column sizes and the flood loads become unmanageable, a maximum elevation of 15 feet exists for the use of this type of foundation. Figure 4-3. Profile of Case B foundation type (see Appendix A for additional drawings) 4.2.3 Open Foundation: Timber Pile with Concrete Column and Grade Beam (Case C) This foundation is similar to the steel pipe pile with concrete column and grade beam foundation (Case B). Elevations as high as 15 feet can be achieved for wind speeds up to 150 mph for both one- and two-story structures. However, because wood piles have a lower strength to resist the loads than steel piles, approximately twice as many timber piles are needed to resist loads imposed on the house and the exposed portions of the foundation (see Figure 4-4). While treated to resist rot and damage from insects, wood piles may become vulnerable to damage from wood destroying organisms in areas where they are not constantly submerged by groundwater. If constantly submerged, there is not enough oxygen to sustain fungal growth and insect colonies; if only periodically submerged, the piles can have moisture levels and oxygen levels sufficient to sustain wood destroying organisms. Consultation with local design professionals in the area familiar with the use and performance of driven treated wood piles will help quantify this potential risk. Grade beams can be constructed at greater depths or alternative pile materials can be selected if wood destroying organism damage is a major concern. Figure 4-4. Profile of Case C foundation type (see Appendix A for additional drawings) 4.2.4 Open Foundation: Concrete Column and Grade Beam with Slabs (Cases D and G) These open foundation types make use of a rigid mat to resist lateral forces and overturning moments. Frictional resistance between the grade beams and the supporting soils resist lateral loads while the weight of the grade beam and the above grade columns resist uplift. Case G (foundation with slab) contains additional reinforcement to tie the on-grade slab to the grade beams to provide additional weight to resist uplift (see Figure 4-5). With the integral slab, elevations up to 15 feet above grade are achievable. Without the slab (as for Case D), the designs as detailed are limited to 10-foot elevations (see Figure 4-6). Unlike the deep driven pile foundations, both shallow grade beam foundation styles can be undermined by erosion and scour if exposed to waves and high flow velocities. Neither style of foundation should be used where anticipated erosion or scour would expose the grade beam. Figure 4-5. Profile of Case G foundation type (see Appendix A for additional drawings) 4.2.5 Closed Foundation: Reinforced Masonry - Crawlspace (Case E) The reinforced masonry with crawlspace type of foundation utilizes conventional construction similar to foundations used outside of SFHAs. Footings are cast-in-place reinforced concrete; walls are constructed with reinforced masonry (see Figure 4-7). The foundation designs presented in Appendix A permit elevated homes to be raised to 8 feet. Higher elevations are achievable with larger or more closely spaced reinforcing steel or with walls constructed with thicker masonry. The required strength of a masonry wall is determined by breaking wave loads for wall heights 3 feet or less, by non-breaking waves and hydrodynamic loads for taller walls, and by uplift for all walls. Perimeter footing sizes are controlled by uplift and must be relatively large for short foundation walls. The weight of taller walls contributes to uplift resistance and allows for smaller perimeter footings. Solid grouting of perimeter walls is recommended for additional weight and improved resistance to water infiltration. Figure 4-6. Profile of Case D foundation type (see Appendix A for additional drawings) Interior footing sizes are controlled by gravity loads and by the bearing capacity of the supporting soils. Since the foundation designs are based on relatively low bearing capacities, obtaining soils tests for the building site may allow the interior footing sizes to be reduced. The crawlspace foundation walls incorporate NFIP required flood vents, which must allow floodwaters to flow into the crawlspace. In doing so, hydrostatic, hydrodynamic, and breaking wave loads are reduced. Crawlspace foundations are vulnerable to scour and flood forces and should not be used in Coastal A Zones; the NFIP prohibits their use in V Zones. 4.2.6 Closed Foundation: Reinforced Masonry - Stem Wall (Case F) The reinforced masonry stem walls (commonly referred to as chain walls in portions of the Gulf Coast) type of foundation also utilizes conventional construction to contain fill that supports the floor slab. They are constructed with hollow masonry block with grouted and reinforced cells (see Figure 4-8). Full grouting is recommended to provide increased weight, resist uplift, and improve longevity of the foundation. The amount and size of the reinforcement are controlled primarily by the lateral forces created by the retained soils and by surcharge loading from the floor slab and imposed live loads. Because the retained soils can be exposed to long duration flooding, loads from saturated soils should be considered in the analyses. The lateral forces on stem walls can be relatively high and even short cantilevered stem walls (those not laterally supported by the floor slab) need to be heavily reinforced. Tying the top of the stem walls into the floor slab provides lateral support Figure 4-7. Profile of Case E foundation type (see Appendix A for additional drawings) for the walls and significantly reduces reinforcement requirements. Because backfill needs to be placed before the slab is poured, walls that will be tied to the floor slab need to be temporarily braced when the foundation is backfilled until the slab is poured and cured. Figure 4-8. Profile of Case F foundation type (see Appendix A for additional drawings) NOTE: Stem wall foundations are vulnerable to scour and should not be used in Coastal A Zones without a deep footing. The NFIP prohibits the use of this foundation type in V Zones. 5 foundation selection 5- Building on strong and safe foundations coastal zone, wind speed, and elevation requirements, all of which have been discussed in the previous chapters. The following types of foundation designs are presented in this manual: Open Foundations n Timber pilen Steel pipe pile with concrete column and grade beamn Timber pile with concrete column and grade beamn Concrete column and grade beamn Concrete column and grade beam with slab Closed Foundations n Reinforced masonry – crawlspacen Reinforced masonry – stem wall Each of these foundation types designed for the Gulf Coast region have advantages and disadvantages that must be taken into account. Modifications to the details and drawings might be needed to incorporate specific house footprints, elevation heights, and wind speeds to a given foundation type. Consultation with a licensed professional engineer is encouraged prior to beginning construction. The foundation designs and materials specified in this document are based on principles and practices used by structural engineering professionals with years of coastal construction experience. This manual has been prepared to make the information easy to understand. Guidance on the use of the foundation designs recommended in this manual is provided in Appendix B. Examples of how the foundation designs in this manual can be used with some of the houses in the publication A Pattern Book for Gulf Coast Neighborhoods are presented in Appendix B. Design drawings for each of the foundation types are presented in Appendix A, and any assumptions used in these designs are in Appendix C. 5.2 Foundation Design Considerations The foundation designs proposed are suitable for homes whose dimensions, weights, and roof pitches are within certain ranges of values. A licensed professional engineer should confirm the appropriateness of the foundation design of homes whose dimensions, weights, or roof pitches fall outside of those defined ranges. Most of the foundation designs are based on a 14-foot wide (maximum) by 24-foot deep (minimum) “module” (see Figure 5-1). From this basic building block, foundations for specific homes can be developed. For example, if a 30-foot deep by 42-foot wide home is to be constructed, the foundation can be designed around three 14-foot wide by 30-foot deep sections. If a 24-foot foundation selection 5 5- deep by 50-foot wide home is desired, four 12.5-foot wide by 24-foot deep sections can be used. If a 22-foot deep home is desired, the foundation designs presented here should only be used after a licensed professional engineer determines that they are appropriate since the shallow depth of the building falls outside the range of assumptions used in the design. The licensed professional engineer should also consider the following: n Local soil conditions. The piling foundations have been developed for relatively soft subsurface soils. Presumptive gravity loading values of 8 tons per pile, uplift loads of 4 tons per pile, and lateral loads of 1 ton per pile were used in these designs. Soil testing on the site may determine that fewer piles are needed to support the home, and the reduced cost of driving fewer piles could justify the cost of soils testing and redesign. Soils test should also be considered to validate the assumptions made. n Building weight. The foundations have been designed to resist uplift forces resulting from a relatively light structure. If the actual home is heavier (e.g., from the use of concrete composite siding or steel framing), it may be cost-effective to reanalyze and redesign the footings. This is particularly true for a home that doesn’t need to be elevated more than several feet or has short foundation walls that can help resist uplift. Basic Module30' x 42' Home24' Minimum14' Maximum42' 14'14'14' 30' 28’ x 50’ Home50’ 28’ 12.5’12.5’12.5’12.5’ Figure 5-1. Schematic of a basic module and two footprints n Footprint complexity. By necessity, the foundations have been designed for relatively simple rectangular footprints. If the actual footprint of the home is relatively complex, the engineer may need to consider torsional wind loading, differential movement among the “modules” that make up the house, concentrated loading in the home’s floor and roof diaphragms, and shear wall placement. 5.3 Cost Estimating Cost information that the homebuilders can use to estimate the cost of installing the foundation systems proposed in this manual are presented in Appendix E. These cost estimates are from information provided by local contractors and are based on May 2006 prices. 5.4 How to Use This Manual The rest of this chapter is designed to provide the user with step by step procedures for the information provided in this document. 1. Determine location of the dwelling on a general map. Identify the location relative to key features such as highways and bodies of water. An accurate location is essential for using flood and wind speed maps in subsequent steps of the design process. 2. Determine location of dwelling on the appropriate FIRM n Determine the flood insurance risk zone from the FIRM (Select V Zone, Coastal A Zone, non-Coastal A Zone, or other). Refer to FEMA 255, Guide to Flood Maps, How to Use Flood Maps to Determine Flood Risk for a Property, for instructions. For the Gulf Coast, the FEMA Hurricane Katrina Flood Recovery Advisories should be used until the Gulf Coast is restudied and remapped. New flood maps are scheduled to be completed in 2006. n Determine the BFE or the interim Advisory Base Flood Elevations (ABFEs) for the location from the FIRM. If the dwelling is outside of floodprone areas, it only needs to be designed for gravity and appropriate wind loads. Seismic events are considered too rare for the Gulf Coast to control the design and analysis. FIRM Panel No. ____________________ Flood Insurance Risk Zone ____________________ Base Flood Elevation (BFE) or Advisory Base Flood Elevation (ABFE) ____________________ 3. Identify the local building code. Several Gulf States are adopting new building codes to govern residential construction. Several parishes, counties, and towns in Louisiana and Mississippi have adopted the IBC and the IRC to govern construction. This document assumes that the IRC governs the design and construction requirements. 4. Identify the local freeboard requirements and DFE. Using either the local building codes, local floodplain ordinances, data obtained from local building officials, or personal preferences (only if greater than minimum requirements), determine the minimum freeboard above the BFE or ABFE. The DFE is the sum of the BFE or ABFE and freeboard values. 5. Determine the required Design Wind Velocity. The IRC references ASCE 7-02 as the source of the wind speed information. The IRC will be used as the source of all individual and combined loads. 6. Establish the topographic elevation of the building site and the dwelling. Elevations can be obtained from official topographic maps published by the National Geodetic Survey and/or as established or confirmed by a surveyor. n If the dwelling and its surrounding site are above the DFE, no flood forces need to be considered. n If the desired topographic elevation is below the DFE, the dwelling must be elevated above the BFE or ABFE. County/Parish/City ____________________ Building Code ____________________ Building Code Date ____________________ Base Flood Elevation (BFE) or Advisory Base Flood Elevation (ABFE) ______________ Freeboard + ______________ Design Flood Elevation ______________ Design Wind Velocity ______________________________ Wind Exposure Category ______________________________ Source of Topo Elevation ______________________________ Topo Elevation (Site) ______________________________ 7. Determine the height of the base of the dwelling above grade. Subtract the lowest ground elevation at the building from the lowest elevation of the structure (i.e., bottom of lowest horizontal structural member). 8. Determine the general soil classification for the site. To determine the load capacity of the soil, the soil must first be classified according to its strength groupings. For purposes of using this manual, the classification system has been greatly simplified into two groups commonly found in coastal areas along the Gulf of Mexico States: (1) loose granular, cohesionless (having little or no clay content) soils and (2) soft, cohesive (principally clayey content) soils. 9. Determine the type of foundation to be used to support the structure. Depending on the location of the dwelling, design wind speed, and local soil conditions documented above, select the desired or required type of foundation. Note that more than one solution may be possible. Refer to Chapter 4 for the potential foundation designs that can be used within the flood zones determined from the FIRM maps. Drawings in Appendix A illustrate the construction details for each of the foundations. Refer to the drawings for further direction and information about the needs for each type of unit. 10. Evaluate alternate foundation type selections. The choice of foundation type may be on the basis of least cost or to provide a personal choice, functional, or aesthetic need at the site. Refer to Appendix E for guidance on preparing cost estimates. Functional needs such as provisions for parking, storage, or other non-habitable uses for the area beneath the living space should be considered in the selection of the foundation design. Aesthetic or architectural issues (i.e., appearance) also must be included in the evaluation process. Guidance for the architectural design considerations can be obtained from A Pattern Book for Gulf Coast Neighborhoods by the Mississippi Governor’s Commission on Recovery, Rebuilding and Renewal (see Appendix B) and from many other sources. As part of the final analysis, it is strongly recommended that the selection and evaluation process be coordinated with or reviewed by knowledgeable contractors or design professionals to arrive at the best solution to fulfill all of the regulatory and functional needs for the construction. 11. Select the foundation design. If the home’s dimensions, height, roof pitch, and weight are within the ranges used to develop these designs, the foundation designs can be used “as is.” However, if the proposed structure has dimensions, height, roof pitch, or weights that fall Design Flood Elevation ______________________________ Topo Elevation ______________________________ Elevation Dimension ______________________________ Soil Classification ______________________________ outside of the range of values used, a licensed professional engineer should be consulted. The materials presented in the appendices should help reduce the engineering effort needed to develop a custom design. Figure 5-2 is a foundation selection decision tree for determining which foundation design to use based on the requirements of the home. Table 5-1 shows which foundation design cases can be used for the home based on height of elevation and wind velocity. Because the designs are good for a range of buildings, they will be conservative for some applications. A licensed professional engineer will be able to provide value engineering and may produce a more efficient design that reduces construction costs. 5.5 Design Examples The foundation designs were developed to allow a “modular approach” for developing foundation plans. In this approach, individual rectangular foundation components can be assembled into non-rectangular building footprints (see Figures 5-3 through 5-5). Appendix D provides detailed calculations and analysis for open and closed foundation designs. There are, however, a few rules that must be followed when assembling the modules: 1. The eave-to-ridge dimension of the roof is limited to 23 feet. The upper limit on roof height is to limit the lateral forces to those used in developing the designs. 2. Roof slopes shall not be shallower than 3:12 or steeper than 12:12. For a 12:12 roof pitch, this corresponds to a 42-foot deep home with a 2-foot eave overhang. 3. The “tributary load depth” of the roof framing shall not exceed 23 feet, including the 2- foot maximum roof overhang. This limit is placed to restrict uplift forces on the windward foundation elements to those forces used in developing the design. As a practical matter, clear span roof trusses are rarely used on roofs over 42 feet deep; therefore, this limit should not be unduly restrictive. The roof framing that consists of multiple spans will require vertical load path continuity down through the interior bearing walls to resist uplift forces on the roof. Load path continuity can be achieved in interior bearing walls using many of the same techniques used on exterior bearing walls. 4. On the perimeter foundation wall designs (Cases E and F), foundation shear walls must run the full depth of the building module, and shear walls can not be spaced more than 42 feet apart. 5. All foundation modules shall be at least 24 feet deep and at least 24 feet long. Although the basic module is limited to 42 feet long, longer home dimensions can be developed, provided that the roof does not extend beyond the building envelope as depicted in Figure 2 of the Introduction. Foundation TypesA = Timber pileB = Steel pipe pile with concrete column and grade beamC = Timber pile with concrete column and grade beamD = Concrete column and grade beamE = Reinforced masonry – crawlspaceF = Reinforced masonry – stem wallG = Concrete column and grade beam with slab Figure 5-2. Foundation Selection Decision Tree Table 5-1. Foundation Design Cases Based on Height of Elevation and Wind Velocity Wind Velocity of 120 to 150 (mph) Height (H) (ft) V Zone Coastal A Zone* Non-Coastal A Zone One-Story Dwelling < 4 A,B,C A,B,C,D,G A,B,C,D,E,F,G 5 A,B,C A,B,C,D,G A,B,C,D,E,G 6 A,B,C A,B,C,D,G A,B,C,D,E,G 7 A,B,C A,B,C,D,G A,B,C,D,E,G 8 A,B,C A,B,C,D,G A,B,C,D,E,G 9 A,B,C A,B,C,G A,B,C,G 10 A,B,C A,B,C,G A,B,C,G 11 B,C B,C,G B,C,G 12 B,C B,C,G B,C,G 13 B,C B,C,G B,C,G 14 B,C B,C,G B,C,G 15 B,C B,C,G B,C,G Two-Story Dwelling < 4 A,B,C A,B,C,D,G A,B,C,D,E,F,G 5 A,B,C A,B,C,D,G A,B,C,D,E,G 6 A,B,C A,B,C,D,G A,B,C,D,E,G 7 A,B,C A,B,C,D,G A,B,C,D,E,G 8 A,B,C A,B,C,D,G A,B,C,D,E,G 9 A,B,C A,B,C,G A,B,C,G 10 A,B,C A,B,C,G A,B,C,G 11 B,C B,C,G B,C,G 12 B,C B,C,G B,C,G 13** B,C B,C B,C 14** B,C B,C B,C 15** B,C B,C B,C * In the Coastal A Zone, the tops of all footings and grade beams in Cases D and G foundations must be placed below the maximum estimated erosion and scour depth. ** Some foundation designs are not appropriate for two-story dwelling for a design wind speed of 150 mph. See individual design drawings for more details. Foundation Types A = Timber pile B = Steel pipe pile with concrete column and grade beam C = Timber pile with concrete column and grade beam D = Concrete column and grade beam E = Reinforced masonry – crawlspace F = Reinforced masonry – stem wall G = Concrete column and grade beam with slab Figure 5-3. “T” shaped modular design Note A: Overall building dimensions can exceed 42 feet. The vertical dimensions from the eave to the ridge roof shall not exceed 23 feet. Module 1Module 2Module 1Module 3Module 2Note ABuilding FootprintAlternative 1Alternative 224’ - 42’ 24’ - 42’ 24’ - 42’ 24’ MinimumNote A Module 1Module 1Module 2Module 2Note A24’ - 42’ 24’ - 42’ 24’ MinimumNote ABuilding FootprintAlternative 1Alternative 2 Figure 5-4. “L” shaped modular design Note A: Overall building dimensions can exceed 42 feet. The vertical dimensions from the eave to the ridge roof shall not exceed 23 feet. Figure 5-5. “Z” shaped modular design Note A: Overall building dimensions can exceed 42 feet. The vertical dimensions from the eave to the ridge roof shall not exceed 23 feet. Module 1Module 1Module 2Module 2Module 3Module 3Note A24' - 42' 24' - 42' 24' - 42' 24' Minimum24' MinimumNoteABuilding FootprintAlternative 1Alternative 2 RECOMMENDED RESIDENTIAL CONSTRUCTION FOR THE GULF COAST A. Foundation Designs A- RECOMMENDED RESIDENTIAL CONSTRUCTION FOR THE GULF COAST B. Pattern Book Design The illustrations in this appendix are from A Pattern Book for Gulf Coast Neighborhoods prepared for the Mississippi Governor’s Rebuilding Commission on Recovery, Rebuilding and Renewal by Urban Design Associates (UDA) of Pittsburgh, Pennsylvania, in November 2005. http://www.mississippirenewal.com/info/plansReports.html B- pattern book design B B- TypeAffordable Housing – “Doublewide Cottage” ContactLaura Anne Bossardt Welsh and Jeremy WelshContact Informationlabwelsh@gmail.comTotal Square Feet1,232Number of Bedrooms4Number of Bathrooms2TimingImmediate/Medium Term/Long TermHousing TypeMobile/Modular/Panelized/Stock PlanElevation0-410-4128'-0'' Floor Planpage 63 top7'11'11'11'11' 44' 14'14' Porch is open and has short spans. Consult with local engineer to determine uplift forces and verify suitability. Figure B-1. Pattern Book for Gulf Coast Neighborhoods Page 63 Top B pattern book design B- Building on strong and safe foundations Housing TypeDetached Single-FamilyContactUrban Design AssociatesContact Informationhttp://www.urbandesignassociates.com/ Total Square Feet1,31